The present study was designed to evaluate the effects of low-level laser (Nd:YAG) therapy and occlusal splints in patients with signs and symptoms of temporomandibular disorders (TMD) characterized with myofascial pain (MP). A total of 30 patients were selected after being diagnosed with MP according to the Research Diagnostic Criteria for Temporomandibular Disorders (RDC/TDM). The patients were divided into three groups. The first group was occlusal splint (OS) group A (n = 10), the second was low-level laser therapy (LLLT) group B (n = 10), and the last group C was placebo (n = 10). LLLT (1,064 nm, 8 j/cm(2), 250 mW, Fotona) was applied to the patients in the study group once a day for 10 days, for a total of ten sessions. The same parameters and application times were used for placebo group, but the patients were not irradiated. The application was on the trigger points. The patients in the OS group were instructed to wear occlusal splints 12 h/day for 3 weeks. Functional examination was based on RDC/TDM, and pressure pain values were obtained with the Visual Analog Scale. Comparisons were made between the groups before and after the treatment according to Wilcoxon, Mann-Whitney U, and Kruskal-Wallis tests. The pain score values decreased significantly after both LLLT (p < 0.05) and occlusal splint therapy (p < 0.05) compared to placebo group (p < 0.05). There was no significant difference between LLLT and OS groups after treatment (p > 0.05). OS and LLLT are effective for decreasing MP. In addition, this particular type of LLLT is as effective as occlusal splint for pain relief.

Objective: The aim of the present study was to evaluate the demographic profile of supernumerary molar (SM) teeth in people in various regions of Turkey. Study Design: A retrospective analysis was carried out on an initial sample of 104,902 subjects drawn from the ortopantographics files from 10 clinics in 7 Turkish cities with documentation of demographic data, the presence of SM teeth, their location, eruption, morphology, and position within the arch. In one region associated patho­logies and treatments were also evaluated. Results: Three hundred fifty-one SMs were detected in 288 patients, constituting 0.33% of the study subjects, with a greater frequency in females (56.4%). SMs were found more frequently in the maxilla (87.7%) than in the mandible, and distomolars (62.9%) were more common than paramolars. The SMs encountered were mostly of conical shape (45.7%), impacted (81.1%), and in a vertical position (52.1). The 33% of SM teeth were related to impacted molar teeth. Conclusion: The most common complication involving these teeth was soft tissue irritation. Demographic data from such specific extensive studies are crucial for improved diagnosis of SM teeth. Early detection allows for measures against complications and more successful therapy. Key words:Supernumerary molars, distomolar, paramolar, prevalence.

No abstract

The purpose of this study was to evaluate the effect of polishing procedures on the color stability of different types of composites after aging. Forty disk-shaped specimens (Ø10×2 mm) were prepared for each composite resin type (an ormocer, a packable, a nanohybrid, and a microhybrid) for a total of 160 specimens. Each composite group was divided into four subgroups according to polishing method (n=10): control (no finishing and polishing), polishing disk, polishing wheel, and glaze material. Color parameters (L*, a*, and b*) and surface roughness were measured before and after accelerated aging. Of the polishing methods, glazed specimens showed the lowest color change (∆E*), ∆L*, and ∆b* values (p<0.05). Of the composite resins, the microhybrid composite showed the lowest ∆E* value, whereas the ormocer showed the highest (p<0.05). For all composite types, the surface roughness of their control groups decreased after aging (p<0.05). In conclusion, all composite resins showed color changes after accelerated aging, with the use of glaze material resulting in the lowest color change.

The aim of this study was to evaluate the influence of different surface treatments (air abrasion, acid etching, laser irradiation) on the surface roughness of a lithium-disilicate-based core ceramic. A total of 40 discs of lithium disilicate-based core ceramic (IPS Empress 2; Ivoclar Vivadent, Schaan, Liechtenstein) were prepared (10 mm in diameter and 1 mm in thickness) according to the manufacturer's instructions. Specimens were divided into four groups (n = 10), and the following treatments were applied: air abrasion with alumina particles (50 μm), acid etching with 5% hydrofluoric acid, Nd:YAG laser irradiation (1 mm distance, 100 mJ, 20 Hz, 2 W) and Er:YAG laser irradiation (1 mm distance, 500 mJ, 20 Hz, 10 W). Following determination of surface roughness (R(a)) by profilometry, specimens were examined with atomic force microscopy. The data were analysed by one-way analysis of variance (ANOVA) and Tukey HSD test (α = 0.05). One-way ANOVA indicated that surface roughness following air abrasion was significantly different from the surface roughness following laser irradiation and acid etching (P < 0.001). The Tukey HSD test indicated that the air abrasion group had a significantly higher mean value of roughness (P < 0.05) than the other groups. No significant difference was found between the acid etching and laser irradiation (both Er:YAG and Nd:YAG) groups (P > 0.05). Air abrasion increased surface roughness of lithium disilicate-based core ceramic surfaces more effectively than acid-etching and laser irradiation.