A laser rapid solidification technique was employed to remelt and refine the microstructure of Al-25wt.%Si and Al-30wt.%Si alloyed layers produced by laser melting. The microstructure of the as-fabricated Al-Si layers consisted of irregular polygonal primary Si crystals of size 5 to 7 µm, fine α-Al dendrites, and Al-Si eutectic. Laser rapid remelting results showed a significant refinement of all the solidified phases with increasing scan speed and decreasing laser power. At the lowest laser power (800W), the sizes of the primary Si crystals were reduced to a sub-micron level and an interwoven network of nano-sized eutectic colonies was obtained. The higher cooling rates, resulted in a reduction in the amount of the α-Al phase especially those surrounding the primary Si, thereby stimulating the eutectic Si fibers to grow from the pre-existing primary Si crystals and increased the proportion of the fibrous eutectic. Transmission electron microscopy revealed fibrous eutectic, which was internally nano-twinned, with a diameter approaching as low as 10-15 nm for the highest cooling rate. The hardness measured by nanoindentation of the eutectic in the remelted Al-25wt.%Si layer increased with decreasing the eutectic spacing (ʎ) reaching a maximum value of 3.15GPa.

A laser rapid solidification technique was employed to remelt and refine the microstructure of Al-25wt.%Si and Al-30wt.%Si alloyed layers produced by laser melting. The microstructure of the as-fabricated Al-Si layers consisted of irregular polygonal primary Si crystals of size 5 to 7 µm, fine α-Al dendrites, and Al-Si eutectic. Laser rapid remelting results showed a significant refinement of all the solidified phases with increasing scan speed and decreasing laser power. At the lowest laser power (800W), the sizes of the primary Si crystals were reduced to a sub-micron level and an interwoven network of nano-sized eutectic colonies was obtained. The higher cooling rates, resulted in a reduction in the amount of the α-Al phase especially those surrounding the primary Si, thereby stimulating the eutectic Si fibers to grow from the pre-existing primary Si crystals and increased the proportion of the fibrous eutectic. Transmission electron microscopy revealed fibrous eutectic, which was internally nano-twinned, with a diameter approaching as low as 10-15 nm for the highest cooling rate. The hardness measured by nanoindentation of the eutectic in the remelted Al-25wt.%Si layer increased with decreasing the eutectic spacing (ʎ) reaching a maximum value of 3.15GPa.

Heterogeneous Al-Si microstructure comprising of sub-micron-scale Al dendrites and nanoscale Al-Si fibrous eutectic was fabricated by processing as-cast Al-20wt.%Si alloy using laser rapid solidification. In situ tension tests explored high tensile strength ( ∼ 600 MPa) and ductility ( ∼ 10%) and high strain hardening rate ( ∼ 7 GPa). Microstructural characterization revealed the plastic codeformation mechanisms between soft Al dendrites and hard nanoscale Al-Si eutectic. The progression of plasticity in nanoscale Al-Si eutectic with increasing applied strain is accommodated by dislocation plasticity in the nano-Al channels and cracking Si nanofibers. The propagation of nano-cracks is suppressed by surrounding Al, retaining good ductility of the sample. IMPACT STATEMENTIn situ tension tests revealed the role of heterogeneous Al-Si microstructure in enhancing strain hardening rate and producing large back stresses and plasticity in sample even after fracture of nanoscale Si fibers.

Laser Surface Remelting (LSR) was applied to arc-melted Al-20Si-0.2Sr, Al-20Si-0.2Ce, and Al-20Si hypereutectic alloys to refine microstructures. Experiments revealed that microstructures in the melt pool varied from fully eutectic to a mixture of Al dendrites and inter-dendritic eutectic. We calculated cooling rates using the Eagar-Tsai model and correlated cooling rates with characteristic microstructures, revealing that a cooling rate on the order of 104 K/s could lead to maximized fully eutectic microstructure morphology. Due to rapid solidification, the Si composition in the LSR eutectic was measured at 18.2 wt.%, higher than the equilibrium eutectic composition of 12.6 wt.%Si. Compared to Al-20Si, Ce addition had no significant effect on the volume fraction of the fully eutectic structure but refined Si fibers to approximately 30 nm in diameter. Sr addition did not further refine the diameter of eutectic Si fibers compared to Al-20Si but increased the volume fraction of the fully eutectic microstructure morphology. The refinement ratio (φ) of the Si fiber diameter from the bottom of the melt pool to the surface for the three alloys was similar, at around 28%. The established correlation between the cooling rate and the size and morphology of the microstructure within the melt pool will enable tailoring of the microstructure in laser-processed as well as deposited alloys for high strength and plasticity.