Nondestructive characterization of solid oxide fuel cell (SOFC) materials has drawn attention owing to the advances in instrumentation that enable in situ characterization during high-temperature cell operation. X-ray photoelectron spectroscopy (XPS) is widely used to investigate the surface of SOFC cathode materials because of its excellent chemical specificity and surface sensitivity. The XPS can be used to analyze the elemental composition and oxidation state of cathode layers from the surface to a depth of approximately 5–10 nm. Any change in the chemical state of the SOFC cathode at the surface affects the migration of oxygen ions to the cathode/electrolyte interface via the cathode layer and causes performance degradation. The objective of this article is to provide a comprehensive review of the adoption of XPS for the characterization of SOFC cathode materials to understand its degradation mechanism in absolute terms. The use of XPS to confirm the chemical stability at the interface and the enrichment of cations on the surface is reviewed. Finally, the strategies adopted to improve the structural stability and electrochemical performance of the LSCF cathode are also discussed.
Understanding the impact of sintering temperature on the physical and chemical properties of Ni-BaCe0.54Zr0.36Y0.1O3-δ (Ni-BCZY) composite anode is worthy of being investigated as this anode is the potential for protonic ceramic fuel cell (PCFC) application. Initially, NiO–BCZY composite powder with 50 wt% of NiO and 50 wt% of BCZY is prepared by the sol–gel method using citric acid as the chelating agent. Thermogravimetric analysis indicates that the optimum calcination temperature of the synthesised powder is 1100 °C. XRD result shows that the calcined powder exists as a single cubic phase without any secondary phase with the lattice parameter (a) of 4.332 Å. FESEM analysis confirms that the powder is homogeneous and uniform, with an average particle size of 51 ± 16 nm. The specific surface area of the calcined powder measured by the Brunauer–Emmett–Teller (BET) technique is 6.25 m2/g. The thickness, porosity, electrical conductivity and electrochemical performance of the screen-printed anode are measured as a function of sintering temperature (1200–1400 °C). The thickness of the sintered anodes after the reduction process decreases from 28.95 μm to 26.18 μm and their porosity also decreases from 33.98% to 26.93% when the sintering temperature increases from 1200 °C to 1400 °C. The electrical conductivities of the anodes sintered at 1200 °C, 1300 °C and 1400 °C are 443 S/cm, 633 S/cm and 1124 S/cm at 800 °C, respectively. Electrochemical studies showed that the anode sintered at 1400 °C shows the lowest area specific resistance (ASR) of 1.165 Ω cm2 under a humidified (3% H2O) gas mixture of H2 (10%) and N2 (90%) at 800 °C. Further improvement of the anode’s performance can be achieved by considering the properties of the screen-printing ink used for its preparation.
Two-dimensional (2D) electron back scattered diffraction (EBSD) is a powerful tool for microstructural characterization of crystalline materials. EBSD enables visualization and quantification of the effect of synthesis methods on the microstructure of individual grains, thus correlating the microstructure to mechanical and electrical efficiency. Therefore, this work was designed to investigate the microstructural changes that take place in the Ni-SDC cermet anode under different synthesis methods, such as the glycine–nitrate process (GNP) and ball-milling. EBSD results revealed that different grain size and distribution of Ni and SDC phases considerably influenced the performance of the Ni–SDC cermet anodes. The performance of the Ni–SDC cermet anode from GNP was considerably higher than that of Ni-SDC from ball-milling, which is attributed to the triple-phase boundary (TPB) density and phase connectivity. Due to the poor connectivity between the Ni and SDC phases and the development of large Ni and SDC clusters, the Ni-SDC cermet anode formed by ball milling had a lower mechanical and electrical conductivity. Moreover, the Ni–SDC cermet anode sample obtained via GNP possessed sufficient porosity and did not require a pore former. The length and distribution of the active TPB associated with phase connectivity are crucial factors in optimizing the performance of Ni-SDC cermet anode materials. The single cell based on the Ni–SDC composite anode prepared through GNP exhibited a maximum power density of 227 mW/cm2 and 121 mW/cm2 at 800 °C in H2 and CH4, respectively.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.