No abstract

The susceptibility of millimeter waveform propagation to blockages limits the coverage of millimeterwave (mmWave) signals. To overcome blockages, we propose to leverage two-hop device-to-device (D2D) relaying. Using stochastic geometry, we derive expressions for the downlink coverage probability of relay-assisted mmWave cellular networks when the D2D links are implemented in either uplink mmWave or uplink microwave bands. We further investigate the spectral efficiency (SE) improvement in the cellular downlink, and the effect of D2D transmissions on the cellular uplink. For mmWave links, we derive the coverage probability using dominant interferer analysis while accounting for both blockages and beamforming gains. For microwave D2D links, we derive the coverage probability considering both line-of-sight (LOS) and non-line-of-sight (NLOS) propagation. Numerical results show that downlink coverage and SE can be improved using two-hop D2D relaying. Specifically, microwave D2D relays achieve better coverage because D2D connections can be established under NLOS conditions. However, mmWave D2D relays achieve better coverage when the density of interferers is large because blockages eliminate interference from NLOS interferers. The SE on the downlink depends on the relay mode selection strategy, and mmWave D2D relays use a significantly smaller fraction of uplink resources than microwave D2D relays.

We consider the problem of energy-efficient point-to-point transmission of delay-sensitive data (e.g. multimedia data) over a fading channel. Existing research on this topic utilizes either physicallayer centric solutions, namely power-control and adaptive modulation and coding (AMC), or systemlevel solutions based on dynamic power management (DPM); however, there is currently no rigorous and unified framework for simultaneously utilizing both physical-layer centric and system-level techniques to achieve the minimum possible energy consumption, under delay constraints, in the presence of stochastic and a priori unknown traffic and channel conditions. In this report, we propose such a framework. We formulate the stochastic optimization problem as a Markov decision process (MDP) and solve it online using reinforcement learning. The advantages of the proposed online method are that (i) it does not require a priori knowledge of the traffic arrival and channel statistics to determine the jointly optimal power-control, AMC, and DPM policies; (ii) it exploits partial information about the system so that less information needs to be learned than when using conventional reinforcement learning algorithms; and (iii) it obviates the need for action exploration, which severely limits the adaptation speed and run-time performance of conventional reinforcement learning algorithms. Our results show that the proposed learning algorithms can converge up to two orders of magnitude faster than a state-of-the-art learning algorithm for physical layer power-control and up to three orders of magnitude faster than conventional reinforcement learning algorithms.Delay-sensitive communication systems often operate in dynamic environments where they experience time-varying channel conditions (e.g. fading channel) and dynamic traffic loads (e.g. variable bit-rate). In such systems, the primary concern has typically been the reliable delivery of data to the receiver within a tolerable delay. Increasingly, however, battery-operated mobile devices are becoming the primary means by which people consume, author, and share delay-sensitive content (e.g. real-time streaming of multimedia data, videoconferencing, gaming etc.). Consequently, energy-efficiency is becoming an increasingly important design consideration. To balance the competing requirements of energy-efficiency and low delay, fast learning algorithms are needed to quickly adapt the transmission decisions to the time-varying and a priori unknown traffic and channel conditions.Existing research that addresses the problem of energy-efficient wireless communications can be roughly divided into two categories: physical (PHY) layer-centric solutions such as power-control and adaptive modulation and coding (AMC); and system-centric solutions such as dynamic power management (DPM). 1 Although these techniques differ significantly, they can all be used to tradeoff delay and energy to increase the lifetime of battery-operated mobile devices [2] [3] [8]. PHY-centric solutions:A plethora of existin...

Abstract-The proliferation of wireless multihop communication infrastructures in office or residential environments depends on their ability to support a variety of emerging applications requiring real-time video transmission between stations located across the network. We propose an integrated cross-layer optimization algorithm aimed at maximizing the decoded video quality of delay-constrained streaming in a multihop wireless mesh network that supports quality-of-service. The key principle of our algorithm lays in the synergistic optimization of different control parameters at each node of the multihop network, across the protocol layers-application, network, medium access control, and physical layers, as well as end-to-end, across the various nodes. To drive this optimization, we assume an overlay network infrastructure, which is able to convey information on the conditions of each link. Various scenarios that perform the integrated optimization using different levels ("horizons") of information about the network status are examined. The differences between several optimization scenarios in terms of decoded video quality and required streaming complexity are quantified. Our results demonstrate the merits and the need for cross-layer optimization in order to provide an efficient solution for real-time video transmission using existing protocols and infrastructures. In addition, they provide important insights for future protocol and system design targeted at enhanced video streaming support across wireless mesh networks.Index Terms-Cross-layer strategies, distributed video streaming optimization, quality-of-service (QoS), wireless mesh networks.