Measurements of droplet size in optically-thick, non-evaporating, shear-driven sprays have been made using ultra-small angle x-ray scattering (USAXS). The sprays are produced by orifice-type nozzles coupled to diesel injectors, with measurements conducted from 1-24 mm from the orifice, spanning from the optically-dense near-nozzle region to more dilute regions where optical diagnostics are feasible. The influence of nozzle diameter, liquid injection pressure, and ambient density were examined. The USAXS measurements reveal few if any nanoscale droplets, in conflict with a popular computational model of diesel spray breakup. The average droplet diameter rapidly decreases with downstream distance from the nozzle until a plateau value is reached, after which only small changes are seen in droplet diameter. This plateau droplet size is consistent with the droplets being small enough to be stable with respect to further breakup. Liquid injection pressure and nozzle diameter have the biggest impact on droplet size, while ambient density has a smaller effect.

Making quantitative measurements of the vapor distribution in a cavitating nozzle is difficult, owing to the strong scattering of visible light at gas-liquid boundaries and wall boundaries, and the small length and time scales involved. The transparent models required for optical experiments are also limited in terms of maximum pressure and operating life. Over the past few years, xray radiography experiments at Argonne's Advanced Photon Source have demonstrated the ability to perform quantitative measurements of the line of sight projected vapor fraction in submerged, cavitating plastic nozzles. In this paper, we present the results of new radiography experiments performed on a submerged beryllium nozzle 520 microns in diameter, with a length/diameter ratio of 6. Beryllium is a light, hard metal that is very transparent to x-rays due to its low atomic number. We present quantitative measurements of cavitation vapor distribution conducted over a range of non-dimensional cavitation and Reynolds numbers, up to values typical of gasoline and diesel fuel injectors. A novel aspect of this work is the ability to quantitatively measure the area contraction along the nozzle with high spatial resolution. Analysis of the vapor distribution, area contraction and discharge coefficients are made between the beryllium nozzle, and plastic nozzles of the same nominal geometry. When gas is dissolved in the fuel, the vapor distribution can be quite different from that found in plastic nozzles of the same dimensions, although the discharge coefficients are unaffected. In the beryllium nozzle, there were substantially fewer machining defects to act as nucleation sites for the precipitation of bubbles from dissolved gases in the fuel, and as such its effect on the vapor distribution was greatly reduced.

The flow inside direct-injection diesel nozzles is strongly influenced by the local geometry. Deviations from the design geometry and nonuniformities along the fuel’s flow path can alter the expected spray behavior. The influence of small-scale variations in the internal geometry is not well understood due to a lack of data available to experimentalists and modelers that resolve such features. To address the need for more accurate geometry measurements that also quantify the error bounds on manufacturing variability, the 7-BM beamline of the Advanced Photon Source at Argonne National Laboratory has been customized to obtain high-resolution X-ray tomography of injection nozzles. In this article, we present results for several diesel injectors provided by the Engine Combustion Network. The imaging setup was optimized to measure dense metallic samples at high signal-to-noise ratio using projection imaging. To improve contrast, multiple images were recorded at each rotation angle. Phase shifting effects, which amplify the uncertainty in locating nozzle boundaries, were minimized by reducing the propagation distance of the X-rays between the nozzle and detector. Such improvements to the imaging technique enabled the nozzle hole diameter to be measured with an accuracy of 1.8 µm, which takes into account the pixel resolution as well as the properties of the imaging setup and the geometric analysis. The high spatial resolution allows the nozzle hole inlet corner radius to be azimuthally resolved. For the sample set under consideration, these new measurements reveal that non-hydroground injectors have a distribution of radii which typically vary by more than a factor of two. An azimuthally varying radius of curvature at the hole inlet is expected to result in highly asymmetric cavitation. Skeletal wireframe models of the nozzle hole geometries suitable for computational fluid dynamics mesh generation have been developed, in addition to full three-dimensional isosurfaces; these data have been made publicly available online.

the instantaneous ROI and to provide experimental data with parametric variations useful for numerical model validations. Results show a strong relationship between the steady partial needle lift and the ROI. The effect is non-linear, and also strongly dependent on the injection pressure. The steady lift value at which the needle ceases to influence the ROI increases with the injection pressure. Finally, a transient analysis is presented, showing that the needle velocity may considerably affect the instantaneous ROI, because of the volume displaced inside the nozzle. Results presented in this study show that at constant injection pressure and energizing time, this injector has the potential to control many aspects of the ROI and thus, the heat release rate. Also, data presented are useful for numerical model validations, which would provide detailed insight into the physical processes that drive these observations, and potentially, to the effects of these features on combustion performance.

No abstract