Plant biomass is an important parameter for crop management and yield estimation. However, since biomass cannot be determined non-destructively, other plant parameters are used for estimations. In this study, plant height and hyperspectral data were used for barley biomass estimations with bivariate and multivariate models. During three consecutive growing seasons a terrestrial laser scanner was used to establish crop surface models for a pixel-wise calculation of plant height and manual measurements of plant height confirmed the results (R 2 up to 0.98). Hyperspectral reflectance measurements were conducted with a field spectrometer and used for calculating six vegetation indices (VIs), which have been found to be related to biomass and LAI: GnyLi, NDVI, NRI, RDVI, REIP, and RGBVI. Furthermore, biomass samples were destructively taken on almost the same dates. Linear and exponential biomass regression models (BRMs) were established for evaluating plant height and VIs as estimators of fresh and dry biomass. Each BRM was established for the whole observed period and pre-anthesis, which is important for management decisions. Bivariate BRMs supported plant height as a strong estimator (R 2 up to 0.85), whereas BRMs based on individual VIs showed varying performances (R 2 : 0.07-0.87). Fused approaches, where plant height and one VI were used for establishing multivariate BRMs, yielded improvements in some cases (R 2 up to 0.89). Overall, this study reveals the potential of remotely-sensed plant parameters for estimations of barley biomass. Moreover, it is a first step towards the fusion of 3D spatial and spectral measurements for improving non-destructive biomass estimations. OPEN ACCESSRemote Sens. 2015, 7 11450

Appropriate field management requires methods of measuring plant height with high precision, accuracy, and resolution. Studies show that terrestrial laser scanning (TLS) is suitable for capturing small objects like crops. In this contribution, the results of multitemporal TLS surveys for monitoring plant height on paddy rice fields in China are presented. Three campaigns were carried out on a field experiment and on a farmer's conventionally managed field. The high density of measurement points allows us to establish crop surface models with a resolution of 1 cm, which can be used for deriving plant heights. For both sites, strong correlations (each R 2 ¼ 0.91 between TLS-derived and manually measured plant heights confirm the accuracy of the scan data. A biomass regression model was established based on the correlation between plant height and biomass samples from the field experiment (R 2 ¼ 0.86). The transferability to the farmer's field was supported with a strong correlation between simulated and measured values (R 2 ¼ 0.90). Independent biomass measurements were used for validating the temporal transferability. The study demonstrates the advantages of TLS for deriving plant height, which can be used for modeling biomass. Consequently, laser scanning methods are a promising tool for precision agriculture. © The Authors. Published by SPIE under a Creative Commons Attribution 3.0 Unported License. Distribution or reproduction of this work in whole or in part requires full attribution of the original publication, including its DOI.

Multi-temporal crop surface models (CSMs) are a reliable method for agricultural crop monitoring. They provide 3-dimensional representations of crop canopies, preferably available as a multi-temporal dataset. From the CSMs the spatial distribution of plant height can be derived. The data for the CSMs are captured by remote sensing methods including terrestrial laser scanning (TLS) and imagery from unmanned aerial vehicles (UAVs) combined with computer vision techniques. Previous studies underlined the suitability of both methods. However, it remained an open question if both methods provide actually comparable information. We assume that the differing viewing angles of both sensors influence the resulting CSM and that the UAV-based CSMs contain crop density information due to the nadir sensor position. Therefore, we expect a lower mean plant height and higher variation in the UAV-based CSM. The correlation between plant heights from both methods was analyzed and complemented by using polygon grids for spatial analysis. The polygon grids provide descriptive statistics for each raster cell by zonal statistics to investigate the data's potential as a density measure. Through this analysis it is possible to maximize the extraction of spatial information for larger grid cells though it is not comparable to standard resampling methods. We analyzed CSMs at early, middle, and late growth stages from a barley experiment field and found a high correlation (R² = 0.91) in plant height derived from both methods. The UAV-derived plant height was generally lower than the TLS-derived plant height at all growth stages. However, contrary to the expectations the coefficient of variation was higher in the TLS dataset.

It is known that plant height is a suitable parameter for estimating crop biomass. The aim of this study was to confirm the validity of spatial plant height data, which is derived from terrestrial laser scanning (TLS), as a non-destructive estimator for biomass of paddy rice on the field scale. Beyond that, the spatial and temporal transferability of established biomass regression models were investigated to prove the robustness of the method and evaluate the suitability of linear and exponential functions. In each growing season of two years, three campaigns were carried out on a field experiment and on a farmer's conventionally managed field. Crop surface models (CSMs) were generated from the TLS-derived point clouds for calculating plant height with a very high spatial resolution of 1 cm. High coefficients of determination between CSM-derived and manually measured plant heights (R 2 : 0.72 to 0.91) confirm the applicability of the approach. Yearly averaged differences between the measurements were ~7% and ~9%. Biomass regression models were established from the field experiment data sets, based on strong coefficients of determination between plant height and dry biomass (R : 0.60 to 0.90 and 0.56 to 0.85 for linear and exponential models, respectively). Hence, the suitability of TLS-derived spatial plant height as a non-destructive estimator for biomass of paddy rice on the field scale was verified and the transferability demonstrated.

Unmanned aerial vehicles (UAVs) became popular platforms for the collection of remotely sensed geodata in the last years (Hardin & Jensen 2011). Various applications in numerous fields of research like archaeology (Hendrickx et al., 2011), forestry or geomorphology evolved (Martinsanz, 2012). This contribution deals with the generation of multi-temporal crop surface models (CSMs) with very high resolution by means of low-cost equipment. The concept of the generation of multi-temporal CSMs using Terrestrial Laserscanning (TLS) has already been introduced by Hoffmeister et al. (2010). For this study, data acquisition was performed with a low-cost and low-weight Mini-UAV (< 5kg). UAVs in general and especially smaller ones, like the system presented here, close a gap in small scale remote sensing (Berni et al., 2009;Watts et al., 2012). In precision agriculture frequent remote sensing on such scales during the vegetation period provides important spatial information on the crop status. Crop growth variability can be detected by comparison of the CSMs in different phenological stages. Here, the focus is on the detection of this variability and its dependency on cultivar and plant treatment. The method has been tested for data acquired on a barley experiment field in Germany. In this contribution, it is applied to a different crop in a different environment. The study area is an experiment field for rice in Northeast China (Sanjiang Plain). Three replications of the cultivars Kongyu131 and Longjing21 were planted in plots that were treated with different amounts of N-fertilizer. In July 2012 three UAV-campaigns were carried out. Establishment of ground control points (GCPs) allowed for ground truth. Additionally, further destructive and non-destructive field data were collected. The UAV-system is an MK-Okto by Hisystems (www.mikrokopter.de) which was equipped with the high resolution Panasonic Lumix GF3 12 megapixel consumer camera. The self-built and self-maintained system has a payload of up to 1 kg and an average flight time of 15 minutes. The maximum speed is around 30 km/h and the system can be operated up to a wind speed of less than 19 km/h (Beaufort scale number 3 for wind speed). Using a suitable flight plan stereo images can be captured. For this study, a flying height of 50 m and a 44% side and 90% forward overlap was chosen. The images are processed into CSMs under the use of the Structure from Motion (SfM)-based software Agisoft Photoscan 0.9.0. The resulting models have a resolution of 0.02 m and an average number of about 12 million points. Further data processing in Esri ArcGIS allows for quantitative comparison of the plant heights. The multi-temporal datasets are analysed on a plot size basis. The results can be compared to and combined with the additional field data. Detecting plant height with non-invasive measurement techniques enables analysis of its correlation to biomass and other crop parameters (Hansen & Schjoerring, 2003;Thenkabail et al., 2000) measured in the field. The method presented he...