No abstract

The structures of two antimicrobial peptides (arenicin Ar‐1 and its linear derivative C/S‐Ar‐1) are studied in different solutions and at the air–water interface using spectroscopic methods such as circular dichroism (CD) and infrared reflection absorption spectroscopy (IRRAS) as well as grazing incidence X‐ray diffraction (GIXD) and specular X‐ray reflectivity (XR). Both peptides exhibit similar structures in solution. In the buffer used for most of the experiments the main secondary structure elements are 22 % β‐turn, 38 % β‐sheet and 38 % random coil. The amphiphilic peptides are surface‐active and form a Gibbs monolayer at the air–buffer interface. The surface activity is drastically increased by increasing the ionic strength of the subphase. The β‐sheet layer is quite stable and can be compressed to higher surface pressures. This adsorption layer is very crystalline. Bragg peaks corresponding to an interstrand distance of 4.78 Å and to an end‐to‐end distance have been observed. This end‐to‐end distance can be connected with the observed differences in the layer thickness leading to the assumption that the peptides form a hairpin which is bended depending on the interactions with the counterions.

No abstract

Antimicrobial peptides (AMPs) are important effector molecules of the innate immune system of all species. AMPs are highly selective and can be used as lead structures for the development of new drugs complementing standard antibiotic therapies. Understanding the crucial parameters of peptide-membrane interactions is necessary for elucidation of the molecular mechanisms of action. Phospholipid monolayers, as simple 2D models of the membrane surface, can be effectively used for studies of peptide-membrane interactions. The present study is focused on the recently discovered peptide arenicin-1 (Ar-1), which possesses antibacterial and antifungal activities. A linear derivative with serine residues instead of cysteines (C/S-Ar-1) was additionally used to investigate the influence of the AMP on the phase behavior of lipid monolayers at the air/liquid interface. Using the Langmuir balance technique and IRRAS allows us to conclude that both original and modified arenicins reveal a strong influence on the phase transition of anionic phospholipids (fluidization of the lipid hydrocarbon chains), whereas the thermodynamic properties of the zwitterionic phospholipid layers are not affected. A strong effect of the modified peptide on the ordering of negatively charged phospholipids at the air-water interface compared to zwitterionic phospholipids has been observed using GIXD measurements, supported by IRRAS simulations for the spectral range corresponding to the lipid hydrocarbon chains. At lateral pressures above 30 mN/m, both peptides are squeezed out from zwitterionic lipid monolayers, but remains attached to and partly incorporated in anionic lipid monolayers. This study points at the importance of the interplay between hydrophobic and electrostatic interactions for the membrane disruption by AMPs.

The influence of intermediate degradation products on the hydrolytic degradation of poly[(rac-lactide)-co-glycolide] (PLGA, 50 mol% lactide) at the air-water interface is investigated using the Langmuir film balance. For that purpose, PLGA bulk samples were degraded in aqueous solution for different time periods to generate different sized fragments with varying water solubility. After dissolution in chloroform the water-insoluble degradation products are able to form Langmuir monolayers with an increased elasticity modulus by decreasing molecular weights. Watersoluble degradation products of PLGA were found to be surface active and form an adsorption layer at the airwater interface, which can be further compressed, and revealing a different adsorption behavior in dependence on their composition. The obtained results imply that measured surface area reduction as it is determined in Langmuir monolayer degradation (LMD) experiment is restricted by the effect of the surface activity of adsorbed oligomer fragments during the degradation process. The surface activity of the formed degradation products makes it difficult to derive degradation mechanism from a common LMD experiment. To elucidate the mechanism in detail, dimers, trimers and longer oligomers with known composition and end-groups have to be investigated. Copyright