BackgroundIntegration of first- and second-generation ethanol production can facilitate the introduction of second-generation lignocellulosic ethanol production. Consolidation of the second-generation with the first-generation process can potentially reduce the downstream processing cost for the second-generation process as well as providing the first-generation process with energy. This study presents novel experimental results from integrated first- and second-generation ethanol production from grain and wheat straw in a process development unit. The results were used in techno-economic evaluations to investigate the feasibility of the plant, in which the main co-products were distiller’s dried grains with solubles and biogas.ResultsAn overall glucose to ethanol yield, of 81 % of the theoretical, based on glucose available in the raw material, was achieved in the experiments. A positive net present value was found for all the base case scenarios and the minimal ethanol selling price varied between 0.45 and 0.53 EUR/L ethanol. The revenue increased with combined xylose and glucose fermentation and biogas upgrading to vehicle fuel quality. A decrease in the biogas yield from 80 to 60 % also largely affects the net present value. The energy efficiency for the energy content in products available for sale compared with the incoming energy content varied from 74 to 80 %.ConclusionsOne of the two main configurations can be chosen when designing an integrated first- and second-generation ethanol production plant from grain and straw: that producing biogas or that producing distiller’s dried grains with solubles from the xylose sugars. The choice depends mainly on the local market and prices for distiller’s dried grains with solubles and biogas, since the prices for both co-products have fluctuated a great deal in recent years. In the current study, however, distiller’s dried grains with solubles were found to be a more promising co-product than biogas, if the biogas was not upgraded to vehicle fuel quality. It was also concluded that additional experimental data from biogas production using first- and second-generation substrates are required to obtain improved economic evaluations.

The implementation of biorefineries based on lignocellulosic materials as an alternative to fossil-based refineries calls for efficient methods for fractionation and recovery of the products. The focus for the biorefinery concept for utilisation of biomass has shifted, from design of more or less energy-driven biorefineries, to much more versatile facilities where chemicals and energy carriers can be produced. The sugar-based biorefinery platform requires pretreatment of lignocellulosic materials, which can be very recalcitrant, to improve further processing through enzymatic hydrolysis, and for other downstream unit operations. This review summarises the development in the field of pretreatment (and to some extent, of fractionation) of various lignocellulosic materials. The number of publications indicates that biomass pretreatment plays a very important role for the biorefinery concept to be realised in full scale. The traditional pretreatment methods, for example, steam pretreatment (explosion), organosolv and hydrothermal treatment are covered in the review. In addition, the rapidly increasing interest for chemical treatment employing ionic liquids and deep-eutectic solvents are discussed and reviewed. It can be concluded that the huge variation of lignocellulosic materials makes it difficult to find a general process design for a biorefinery. Therefore, it is difficult to define "the best pretreatment" method. In the end, this depends on the proposed application, and any recommendation of a suitable pretreatment method must be based on a thorough techno-economic evaluation.

BackgroundThe forest biorefinery plays an important part in the evolving circular bioeconomy due to its capacity to produce a portfolio of bio-based and sustainable fuels, chemicals, and materials. To tap into its true potential, more efficient and environmentally benign methods are needed to fractionate woody biomass into its main components (cellulose, hemicellulose, and lignin) without reducing their potential for valorization. This work presents a sequential fractionation method for hardwood based on steam pretreatment (STEX) and hydrotropic extraction (HEX) with sodium xylene sulfonate. By prehydrolyzing the hemicellulose (STEX) and subsequently extract the lignin from the cellulose fraction (HEX), the major wood components can be recovered in separate process streams and be further valorized.ResultsUsing autocatalyzed STEX and HEX, hemicellulose (> 70%) and lignin (~ 50%) were successfully fractionated and recovered in separate liquid streams and cellulose preserved (99%) and enriched (~ twofold) in the retained solids. Investigation of pretreatment conditions during HEX showed only incremental effects of temperature (150–190 °C) and hold-up time (2–8 h) variations on the fractionation efficiency. The hydrolyzability of the cellulose-rich solids was analyzed and showed higher cellulose conversion when treated with the combined process (47%) than with HEX alone (29%), but was inferior to STEX alone (75%). Protein adsorption and surface structure analysis suggested decreased accessibility due to the collapse of the fibrillose cellulose structure and an increasingly hydrophobic lignin as potential reasons.ConclusionThis work shows the potential of sequential STEX and HEX to fractionate and isolate cellulose, hemicellulose, and a sulfur-free lignin in separate product streams, in an efficient, sustainable, and scalable process.Electronic supplementary materialThe online version of this article (10.1186/s13068-018-1346-y) contains supplementary material, which is available to authorized users.

No abstract

No abstract