No abstract

The present paper is aimed at development of functionalized risperidone liposomes for brain targeting through nasal route for effective therapeutic management of schizophrenia. The risperidone liposomes were prepared by thin film hydration method. Various parameters such as lipid ratio and lipid to drug ratio were optimized by using Design-Expert(®) Software to obtain high entrapment with minimum vesicle size. The surface of the optimized liposomes was modified by coating stearylamine and MPEG-DSPE for enhanced penetration to the brain. The formulations were evaluated for vesicle size, zeta potential, and entrapment efficiency. The morphology was studied by Transmission Electron Microscopy (TEM). In vivo efficacy was assessed by performing pharmacokinetic study in Wistar albino rats following intranasal administration of the formulations in comparison to intravenous bolus administration of pure drug. The mean vesicle size of optimized liposomes ranged from 90 to 100nm with low polydispersity index (<0.5). The entrapment efficiency of optimized liposomes was between 50 and 60%, functionalized liposomes showed maximum entrapment. The TEM images showed predominantly spherical vesicles with smooth bilayered surface. All formulations showed prolonged diffusion controlled drug release. The in vivo results showed that liposomal formulations provided enhanced brain exposure. Among the formulations studied, PEGylated liposomes (LP-16) had shown greater uptake of risperidone into the brain than plasma. High brain targeting efficiency index for LP-16 indicating preferential transport of the drug to brain. The study demonstrated successful formulation of surface modified risperidone liposomes for nasal delivery with brain targeting potential.

Abstract:Gliclazide is practically insoluble in water and its bioavailability is limited by dissolution rate. To enhance the dissolution rate and bioavailability the present study was aimed to formulate solid dispersions using different water soluble polymers such as polyethylene glycol 4000 (PEG 4000), polyethylene glycol 6000 (PEG 6000) using fusion method and polyvinyl pyrrolidone K-30 (PVP K 30) by solvent evaporation method. The interaction of gliclazide with the hydrophilic polymers was studied by Differential Scanning Calorimetry (DSC), Fourier Transformation-Infrared Spectroscopy (FTIR) and X-Ray diffraction analysis. Solid dispersions were characterized for physicochemical properties like drug content, surface morphology and dissolution studies. Various factors like type of polymer and ratio of the drug to polymer on the solubility and dissolution rate of the drug were also evaluated. Pharmacokinetic studies of optimized formulation were compared with pure drug and marketed formulation in wistar rats. The dissolution of the pure drug and solid dispersion prepared with PVP K 30 (1:1) showed 38.3 + 4.5 % and 95 + 5.2 % release respectively within 30 min. Peak plasma concentration of pure drug, solid dispersion (PVP K 30) and marketed formulation was found to be 8.76 + 2.5, 16.04 + 5.5 and 9.24 + 3.6 μg/ml respectively, from these results it was observed that there is two fold increase in peak plasma concentration compared to pure drug. Solid dispersion is an effective technique in increasing solubility, dissolution rate and bioavailability of the poorly soluble drugs.

The purpose of present study was to design, optimize and evaluate osmotically controlled pulsatile release capsule (PRC) of montelukast sodium (MKS) for the prevention of episodic attack of asthma in early morning and associated allergic rhinitis. Assembly of the capsular systems consisted of push, active and plug tablet arranged from bottom to top in hard gelatin capsule. The capsule system was coated with a semi-permeable membrane of cellulose acetate and drilled towards plug side in cap. A three-factor, three-level central composite design (CCD) with ¼ 1 was introduced to execute the experiments and quadratic polynomial model was generated to predict and assess the independent variables with respect to the dependent variables. The composition of optimal formulation was determined as weight of push tablet 138 mg (coded value: þ0.59), plug tablet 60 mg (coded value: þ0.49) and coating weight gain of 8.4 mg (coded value: À0.82). The results showed that the optimal formulation of PRCs had lag time of 4.5 h, release at 6 and 12 h are 61.95% and 96.29%, respectively. The X-ray radiographic imaging study was carried out to monitor the in vivo behavior of developed barium sulfate-loaded PRCs in rabbits under fasting conditions. In vivo pharmacokinetic study revealed T max of 2 h for marketed tablets; however 7 h for PRCs with initial lag time of 4 h. Thus designed capsular system may be helpful for patients with episodic attack of asthma in early morning and associated allergic rhinitis.

The purpose of the study was to formulate and evaluate controlled release chitosan microspheres of mirtazapine (MTZ) to improve the bioavailability by altering the pharmacokinetic profiles of the drug. Chitosan microspheres were prepared to prolong the release of the drug into the systemic circulation. Microspheres were prepared by a single water in oil (w/o) emulsion technique varying the chitosan/drug ratio, stirring speed and concentration of the crosslinking agent (glutaraldehyde). Drug-polymer compatibility studies were carried out using fourier transform infrared spectroscopy (FT-IR) and differential scanning calorimetry (DSC). The microspheres were evaluated for encapsulation efficiency, particle size, surface morphology, swelling index, in vitro release, as well as erosion and in vivo studies in rats. The FT-IR and DSC studies revealed no interaction between drug and polymer. The encapsulation efficiency of different formulation varied from 53 ± 1.2% to 78 ± 1.5%. The mean particle size of the optimized formulation F-14 was 106.4 ± 0.5 μm. Surface morphology revealed that chitosan microspheres were discrete and spherical in shape with a porous surface. The release of MTZ from chitosan microspheres was rapid up to 4 h, and then it was continuously and slowly released up to 48 h. Optimized formulation (F-14) was found to be stable under accelerated storage conditions based on International Conference on Harmonisation guidelines. Pharmacokinetic studies revealed that the optimized formulation showed significant increases in systemic exposure (AUC = 177.70 ± 7.39 μg·h/mL), half-life (4.72 ± 0.46 h) and reduced clearance (0.009 ± 0.0001 L/h) compared to pure drug administration. Hence, the present study demonstrates that controlled release formulation of MTZ microspheres using chitosan can improve pharmacokinetic profiles of MTZ.