No abstract

In order to improve the aqueous solubility and dissolution of Tacrolimus (TAC), amorphous solid dispersions of TAC were prepared by hot melt extrusion with three hydrophilic polymers, Polyvinylpyrrolidone vinyl acetate (PVP VA64), Soluplus® and Hydroxypropyl Cellulose (HPC), at a drug loading of 10% w/w. Molecular modeling was used to determine the miscibility of the drug with the carrier polymers by calculating the Hansen Solubility Parameters. Powder X-ray diffraction and differential scanning calorimetry (DSC) studies of powdered solid dispersions revealed the conversion of crystalline TAC to amorphous form. Fourier transform Infrared (FTIR) spectroscopy results indicated formation of hydrogen bond between TAC and polymers leading to stabilization of TAC in amorphous form. The extrudates were found to be stable under accelerated storage conditions for 3 months with no re-crystallization, indicating that hot melt extrusion is suitable for producing stable amorphous solid dispersions of TAC in PVP VA64, Soluplus® and HPC. Stable solid dispersions of amorphous TAC exhibited higher dissolution rate, with the solid dispersions releasing more than 80% drug in 15 min compared to the crystalline drug giving 5% drug release in two hours. These stable solid dispersions were incorporated into orally-disintegrating tablets in which the solid dispersion retained its solubility, dissolution and stability advantage.

LiCoPO 4 and LiCoPO 4 /C electrode active material was synthesized by a simple single-step protocol namely citric acid-assisted, isopropanol-added sol-gel method. Structural and morphology studies reveal the formation of single-phase products of pristine as well as in situ carbon-coated nano-sized grains of genuine purplecolored product of LiCoPO 4 and black-colored LiCoPO 4 /C due to uniform carbon coatings, respectively. In situ carbon coating was confirmed by scanning transmission electron microscopy imaging which exhibits the in situ nanocarbon coating networks. The electrode active characteristics of the synthesized products confirmed by resolved cyclic voltammograms corresponding to cobalt redox couple (Co 2+ /Co 3+ ) confirm the lithium extraction/insertion reversible processes. Carbon coating ensures better resolved near symmetric redox peaks with increased current profile indicative of enhanced rate capability (Li + extraction/insertion), presumably due to the enhanced electrode conductivity of the host matrix by means of carbon coating.

Background: Sirolimus (SIR) is a macrocyclic lactone antibiotic and used therapeutically as a potent immunosuppressant for prophylaxis of kidney transplant rejection. The development of an oral dosage form is challenging because of very poor aqueous solubility (2.6µg/ml). The oral bioavailability of SIR is only 15-20 % and is affected by food and other drugs. The main reasons for low bioavailability are intestinal degradation by enzymes especially by cytochrome P4503A4, efflux by P-glycoprotein and hepatic first-pass metabolism. Objective: The main objective was to prepare a mouth dissolving film dosage form of amorphous SIR to improve dissolution. Methods: Crystalline SIR was transformed to its form amorphous by milling for 2 h at room temperature. Thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and powder x-ray diffraction (PXRD) were used for characterisation. The stability of amorphous SIR was studied at 4°C and 40°C/75% RH. Amorphous SIR was formulated as oral films by melt extrusion with polyvinylpyrrolidone- vinyl acetate (PVP-VA), Soluplus® and hydroxypropyl cellulose (HPC) as carriers. The films were characterized for drug content, physical state, dissolution profile and stability at 4°C and 40°C/75% RH. Results: The PRXD and DSC confirmed the conversion of crystalline SIR to amorphous form by milling. The solubility of amorphous SIR was several folds higher than its crystalline form, but amorphous SIR was highly unstable at all tested temperatures (4° and 40°C). The extruded films exhibited higher dissolution and stability compared to milled SIR powder alone, but the process of extrusion had some detrimental effect on the chemical stability of amorphous SIR. Conclusion: The film formulations showed a significant improvement in the storage stability of the amorphous form of SIR and the solubility advantage of the amorphous form was evident in the dissolution testing. The oral films can potentially improve the bioavailability of SIR by absorption through the buccal mucosa.