Investigation was carried out to examine the characterization and physicochemical properties of some wood sawdust obtained from Niger Delta Area of Nigeria limited for the purpose of usage as an absorbent for remediation of contaminant in soil environment. Experimental examination was conducted on value, moisture content, bulk density and porosity, iodine number and ash content for the various wood sawdust samples from Obuba and Abura, Opepe/mahogany. The result obtained revealed that the pH value of Obuba red (soft wood) is 5.48, Abura (hard wood) 6.18, opepe/mahogany (hard wood) 5.75 and iroko (soft wood) 5.29, whereas the moisture content value opepe/mahogany and iroko. The result further revealed that the bulk density and the porosity value are as presented, grain volume value are 2.910, 2.475, 1.931, and 2.959, bulk density value are 1.0317, 0.884, 0.2190, 0.4306, 0.5490, and 0.3499 for obuba red, abura, opepe/mahogany and iroko. The iodine number tested demonstrates the following value of 10.20, 6.90, 13.90 and 5:9 and 6.6 for obuba red, abura, opepe/mahogany and iroko. Finally, it was demonstrated that the usefulness of characterization and examination of physicochemical properties of functional components that control and improve the monitoring, predicting and determination of the kinetics values.

This Research investigated the adsorption capacity of locally prepared adsorbents from Egg shells for the removal of fluoride ion in well water. It evaluated the performance of these adsorbents calcinated at 3000C and modified with 1.0M HNO3 (trioxonitrate (v)) acid. Batch adsorber was used to allow for interaction between adsorbent (grounded Egg shells) with water containing fluoride ion. The batch experiment was performed with particle size of 2.12 contact time (60, 120, 180, 240, 300min), mass dosage (5g, 10g, 15g, 20g) and temperature (250C, 300C, 400C, 500C). The modified adsorbent was characterized to determine the physiochemical properties of grounded Egg shells (GE). Also the chemical composition of the modified adsorbent was analyzed to determine the percentage of calcium element required for the uptake of the fluoride ions in water for calcium as 39.68% for grounded Egg shells (GE). Percentage adsorption increased with increase in contact time, mass dosage and temperature for the adsorbent. The adsorption capacity was also determined which also increased with increase in contact time, temperature but decreased with increase in mass dosage at constant time of 60minutes. The pseudo first-order, pseudo second order and intraparticle diffusion kinetic models were fitted into the experimental results. The results obtained indicated that the pseudo first order and intraparticle diffusion models for the grounded Egg shells (GE) reasonably described the adsorption process very well whereas the pseudo second order model was not suitable for a calcinations temperature of 3000C and particle size of 2.12m. The adsorption isotherms were obtained from equilibrium experiment Performed at temperature of 25, 35, 45 and 550C. The result showed that Langmuir and Freundlich isotherm fitted perfectly the experimental data. However, the negative values of Gibb’s free energy indicated that adsorption was favourable and the positive enthalpy change H0 revealed that adsorption process was endothermic while the positive value of the entropy change signified increased randomness with adsorption.

This Research investigated the adsorption capacity of locally prepared adsorbents from Egg shells for the removal of fluoride ion in well water. It evaluated the performance of these adsorbents calcinated at 3000C and modified with 1.0M HNO3 (trioxonitrate (v)) acid. Batch adsorber was used to allow for interaction between adsorbent (grounded Egg shells) with water containing fluoride ion. The batch experiment was performed with particle size of 2.12 contact time (60, 120, 180, 240, 300min), mass dosage (5g, 10g, 15g, 20g) and temperature (250C, 300C, 400C, 500C). The modified adsorbent was characterized to determine the physiochemical properties of grounded Egg shells (GE). Also the chemical composition of the modified adsorbent was analyzed to determine the percentage of calcium element required for the uptake of the fluoride ions in water for calcium as 39.68% for grounded Egg shells (GE). Percentage adsorption increased with increase in contact time, mass dosage and temperature for the adsorbent. The adsorption capacity was also determined which also increased with increase in contact time, temperature but decreased with increase in mass dosage at constant time of 60minutes. The pseudo first-order, pseudo second order and intraparticle diffusion kinetic models were fitted into the experimental results. The results obtained indicated that the pseudo first order and intraparticle diffusion models for the grounded Egg shells (GE) reasonably described the adsorption process very well whereas the pseudo second order model was not suitable for a calcinations temperature of 3000C and particle size of 2.12m. The adsorption isotherms were obtained from equilibrium experiment Performed at temperature of 25, 35, 45 and 550C. The result showed that Langmuir and Freundlich isotherm fitted perfectly the experimental data. However, the negative values of Gibb’s free energy indicated that adsorption was favourable and the positive enthalpy change H0 revealed that adsorption process was endothermic while the positive value of the entropy change signified increased randomness with adsorption.

The simulation of a 270 KTA capacity polyethylene plant was performed using Aspen Hysys version 8.8. A Hysys model of the polyethylene was developed using the polyethylene plant layout of Indorama Eleme Petrochemical Company. A material and energy balance for the various components of the plant was performed manually and with Hysys for comparison. The design of the various components of the Hysys model was performed. The polyethylene reactor was simulated to study the effect of process functional parameters such as reactor dimensions, temperature and pressure. The effect of reactor size and number on polyethylene output was studied by simulating the plant with five continuous stirred tank reactors (CSTRs) in series and a single reactor. The results of the material and energy balance of the various components of the plant were performed manually and with Hysys which showed a maximum deviation of 0.8%. The design results of the sizing parameters for the Multiple and single CSTRs were compared in terms of Volume, Diameter, Height, Spacetime, Space Velocity, and Volumetric flowrate respectively. At 90% Conversion, the multiple CSTRs gave 600 dm 3 , 0.7668 m, 1.198 m, 0.052 hr, 195.83 hr −1 , and 117.5 m 3 /h for the above listed parameters, while the single CSTR gave 6000 dm 3 , 1.721 m, 2.581 m, 0.056 hr, 17.867 hr −1 and 107.2 m 3 /h for the same conversion. The sizing results for each of the five compressors were also compared in terms of the following parameters: Adiabatic Head, Polytropic Head, Adiabatic fluid Head, polytropic Fluid Head, Adiabatic Efficiency, power consumed, polytropic head factor, polytropic exponent and isentropic exponent. The effect of reactor size and number showed that At 90% conversion the multiple CSTRS in series gave a lower volume than the single CSTR for the same conversion, and more Economical than the single CSTR for the same conversion.