iNPn, EndoVac-0, iNPs and SI0 achieved greater irrigant penetration to WL. iNPn was able to collect a median volume of CS (4 mL) similar to that delivered by syringe irrigation (iNPp, SI0 and SI2). An adequate irrigant penetration into lateral canals could not be achieved by any of the systems.

This study evaluated the effect of different protocols for Ca(OH)2 removal on the bond strength (BS) of epoxy resin‐based sealer in long oval root canals. Forty‐eight mandibular incisors with long oval root canals were selected by CBCT. Biomechanical preparation was performed, the samples were filled with Ca(OH)2 paste and distributed in four groups (n = 12): G‐without Ca(OH)2 paste (C); G2‐syringe/needle (SN); G3‐SN + XP‐Endo® Finisher (XPF); G4‐SN + passive ultrasonic irrigation (PUI). After 7 days, Ca(OH)2 was removed and teeth were filled using AHPlus and guttapercha. In four samples from each group, the sealer was manipulated with 0.1% rhodamine to assess sealer penetration by fluorescent laser confocal microscopy (FLCM). Samples were sectioned in slices for BS, scanning electron microscopy, and FLCM analysis. The BS data were analyzed by ANOVA and Tukey tests (α = 0.05). The lowest BS values were found for the SN group (12.89 ± 4.36) compared to C (35.55 ± 10.05), while PUI group presented intermediate values (28.57 ± 9.35) and the XPF group (31.34 ± 9.8) showed values that were sometimes similar to C group and sometimes similar to PUI group (p > .05). The analysis of the adhesive interface showed evident gaps, with the presence of residues between the dentin and the filling material for the SN group, and for C, XPF and PUI groups juxtaposed adhesive interface. FLCM images showed sealer penetration in the dentinal tubules along the entire perimeter for C, XPF, and PUI groups. Ca(OH)2 removal with XPF and PUI from long oval root canals resulted in higher bond strength values compared to SN, besides better sealer penetration on dentinal tubules and juxtaposed adhesive interface.

No abstract

This case report describes a technique in which endodontic treatment and permanent indirect restoration were completed in the same clinical appointment with the aid of a computer-aided design/computer-aided manufacturing (CAD/CAM) system. Two patients were diagnosed with irreversible pulpitis of the mandibular first molar. After access preparation, root canals were located, irrigation was performed until bleeding ceased, and the coronal tooth structure was prepared for indirect restoration. Then, utilizing an interim 3-mm build-up of the endodontic access cavity, a hemi-arch digital scan was performed with an intraoral scanner. Subsequent to digital scanning, restoration design was performed simultaneously with the endodontic procedure. The root canals were shaped using the Race system under irrigation with 2.5% sodium hypochlorite followed by root canal filling. The pulp chamber was subsequently filled with a 3-mm-thick composite resin restoration mimicking the interim build-up previously utilized to facilitate block milling in the CAD/CAM system. Clinical try-in of the permanent onlay restoration was followed by acid etching, application of a 5th generation adhesive, and cementation of the indirect restoration. Once the restoration was cemented, rubber dam isolation was removed, followed by occlusal adjustment and polishing. After 2 years of follow-up, the restorations were esthetically and functionally satisfactory, without complications.

To investigate the influence of the remaining volume of a new intracanal medication based on bioceramic compounds on the bond strength (BS) and formation of an adhesive interface between calcium silicate-based and epoxy resin-based root canal sealers. For this purpose, the specimens were distributed according to the intracanal medication (n = 26): Bio-C Temp (BCT) and Ultracal XS (UXS). The roots were scanned in microCT, and after 7 days, the medication was removed. Then a new scan was performed to evaluate the volume of medication remaining. Subsequently, 40 specimens were redistributed into 2 subgroups (n = 10) and filled according to the sealer used: AH Plus (AHP) and Bio-C Sealer (BCS), to assess the bond strength by using the push-out test, and the adhesive interface by confocal laser fluorescence microscopy (CLSM) and scanning electron microscopy (SEM). The t test showed a smaller remainder of BCT (1.77 ± 0.86) compared with UXS (10.47 ± 5.78), irrespective of the root third evaluated. The BS showed that teeth with BCT + BCS had higher bond strength values (3.70 ± 1.22) when compared to the other groups: BCT + AHP (2.15 ± 1.07), UXS + BCS (3.18 ± 1.09) and UXS + AHP (2.11 ± 1.02) (p<0.001). The cervical third had higher BS when compared with the middle and apical thirds (p < 0.001), and higher number of adhesive failures. The adhesive interface in SEM and CLSM images showed better adaptation for the association between BCT + BCS. Intracanal medication and silicatebased endodontic sealer appeared to interact chemically by forming a biomineralizing layer, allowing for an increase in the bond strength and forming an adhesive interface between the materials, with no or less gap formation.