During the last decade, saliva has emerged as a potentially ideal diagnostic biofluid for noninvasive testing. In this paper, we present an automated, integrated platform useable by minimally trained personnel in the field for the diagnosis of respiratory diseases using human saliva as a sample specimen. In this platform, a saliva sample is loaded onto a disposable microfluidic chip containing all the necessary reagents and components required for saliva analysis. The chip is then inserted into the automated analyzer, the SDReader, where multiple potential protein biomarkers for respiratory diseases are measured simultaneously using a microsphere-based array via fluorescence sandwich immunoassays. The results are read optically, and the images are analyzed by a custom-designed algorithm. The fully automated assay requires as little as 10 μL of saliva sample, and the results are reported in 70 min. The performance of the platform was characterized by testing protein standard solutions, and the results were comparable to those from the 3.5-h lab bench assay that we have previously reported. The device was also deployed in two clinical environments where 273 human saliva samples collected from different subjects were successfully tested, demonstrating the device’s potential to assist clinicians with the diagnosis of respiratory diseases by providing timely protein biomarker profiling information. This platform, which combines non-invasive sample collection and fully automated analysis, can also be utilized in point-of-care diagnostics.

No abstract

The development of a photothermal absorbance detector for use with microfluidic devices is described. Unlike thermooptical techniques that rely on measuring refractive index changes, the solution viscosity is probed by continuously monitoring solution conductivity. Platinum electrodes microfabricated on a quartz substrate and bonded to a substrate containing the microchannels enable contact conductivity measurements. The effects of excitation frequency and voltage, electrode spacing, laser power, and laser modulation (chopping) frequency were evaluated experimentally. In the current configuration a limit of detection of 5 nM for DABSYL-tagged glucosamine was obtained using long injections (to give flat-topped peaks). This corresponds to an absorbance of 4.4 × 10−7 AU. Separation and detection of DABSYL-tagged glycine, proline, and tryptophan is also shown to demonstrate the feasibility of the method. In addition, simulations were used to investigate the applicability of the technique to small volume platforms.

A rapid fabrication and prototyping technique to incorporate microwell arrays with sub-10 μm features within a single layer of microfluidic circuitry is presented. Typically, the construction of devices that incorporate very small architecture within larger components has required the assembly of multiple elements to form a working device. Rapid, facile production of a working device using only a single layer of molded polydimethylsiloxane (PDMS) and a glass support substrate is achieved with the reported fabrication technique. A combination of conventional wet-chemical etching for larger (≥20 μm) microchannel features and focused ion beam (FIB) milling for smaller (≤10 μm) microwell features was used to fabricate a monolithic glass master mold. PDMS/glass hybrid chips were then produced using simple molding and oxygen plasma bonding methods. Microwell structures were loaded with 3 μm antibody-functionalized dye-encoded polystyrene spheres, and a sandwich immunoassay for common cytokines was performed to demonstrate proof-of-principle. Potential applications for this device include highly parallel multiplexed sandwich immunoassays, DNA/RNA hybridization analyses, and enzyme linked immunosorbent assay (ELISA). The fabrication technique described can be used for rapid prototyping of devices wherever submicrometer- to micrometer-sized features are incorporated into a microfluidic device.

The development and application of polyelectrolytic gel electrodes (PGEs) for a microfluidic photothermal absorbance detection system is described. The PGEs are used to measure changes in conductivity based on heat generation by analytes absorbing light and changing the solution viscosity. The PGEs are suitable for direct contact conductivity measurements since they do not degrade with exposure to high electric fields. Both a 2-electrode system with DC voltages and a 3-electrode system with AC voltages were investigated. Experimental factors including excitation voltage, excitation frequency, laser modulation frequency, laser power, and path length were tested. The limits of detection for the 3-electrode and 2-electrode systems are 500 nM and 0.55 nM for DABSYL-tagged glucosamine, respectively. In addition, an electrokinetic separation of a potassium, DABSYL-tagged glucosamine, Rhodamine 6G, and Rhodamine B mixture was demonstrated.