The aim of this research was to characterize soldering alloys of the type Sn–Sb–Ti and to study the ultrasonic soldering of SiC ceramics with a metal–ceramic composite of the type Cu–SiC. The Sn5Sb3Ti solder exerts a thermal transformation of a peritectic character with an approximate melting point of 234 °C and a narrow melting interval. The solder microstructure consists of a tin matrix, where the acicular constituents of the Ti6(Sb,Sn)5 phase and the sharp-edged constituents of the TiSbSn phase are precipitated. The tensile strength of the soldering alloy depends on the Ti content and reaches values from 34 to 51 MPa. The average strength of the solder increases with increasing Ti content. The bond with SiC ceramics is formed owing to the interaction of titanium, activated by ultrasound, with SiC ceramics, forming the (Ti,Si)6(Sb,Sn)5 reaction product. The bond with the metal–ceramic composite Cu–SiC is formed owing to the solubility of Cu in a tin solder forming two phases: the wettable η-Cu6Sn5 phase, formed in contact with the solder, and the non-wettable ε-Cu3Sn phase, formed in contact with the copper composite. The average shear strength of the combined joint of SiC/Cu–SiC fabricated using the Sn5Sb3Ti solder was 42.5 MPa. The Sn–Sb–Ti solder is a direct competitor of the S-Bond active solder. The production of solders is cheaper, and the presence of antimony increases their strength. In addition, the application temperature range is wider.

The aim of this research is to characterize the soldering alloy Zn6Al6Ag, and to study the ultrasonic soldering of an Al2O3/metal–ceramic composite (Al/Al2O3). Zn6Al6Ag solder presents a quasi-eutectic structure with a melting point around 425 °C. The solder microstructure consists of a (Zn) + (Al) matrix, reinforced with a silver AgZn3 phase. A bond with the metal–ceramic composite was formed due to the dissolution of Al in the liquid Zn solder. The Al2O3 particles were put into motion, and a new composite was formed on the boundary. The Zn6Al6Ag solder also wetted the surface of the Al2O3 ceramic. A decisive effect on bond formation was caused by zinc and aluminum, whose oxides were combined with the oxides of ceramic material during in-air soldering. An adhesive bond was formed. The average joint shear strength of Al2O3/metal–ceramic composite (Al/Al2O3) was found to be 23 MPa.

In the present work, the microstructure, phase constitution, and corrosion behavior of binary Sn–xZn alloys (x = 5, 9 and 15 wt.%) were investigated. The alloys were prepared by induction melting of Sn and Zn lumps in argon. After melting, the alloys were solidified to form cast cylinders. The Sn–9Zn alloy had a eutectic microstructure. The Sn–5Zn and Sn–15Zn alloys were composed of dendritic (Sn) or (Zn) and eutectic. The corrosion behavior of the Sn–Zn alloys was studied in aqueous HCl (1 wt.%) and NaCl (3.5 wt.%) solutions at room temperature. Corrosion potentials and corrosion rates in HCl were significantly higher compared to NaCl. The corrosion of the binary Sn–Zn alloys was found to take place by a galvanic mechanism. The chemical composition of the corrosion products formed on the Sn–Zn alloys changed with the Zn weight fraction. Alloys with a higher concentration of Zn (Sn–9Zn, Sn–15Zn) formed corrosion products rich in Zn. The Zn-rich corrosion products were prone to spallation. The corrosion rate in the HCl solution decreased with decreasing weight fraction of Zn. The Sn–5Zn alloy had the lowest corrosion rate. The corrosion resistance in HCl could be considerably improved by reducing the proportion of zinc in Sn–Zn alloys.

No abstract

The aim of the research work was to characterize the soldering alloy type Bi-Ag-Ti and to study the direct soldering of silicon and copper. Bi11Ag1.5Ti solder has a broad melting interval. Its scope depends mainly on the content of silver and titanium. The solder begins to melt at the temperature of 262.5 ∘C and full melting is completed at 405 ∘C. The solder microstructure consists of a bismuth matrix with local eutectics. The silver crystals and titanium phases as BiTi2 and Bi9Ti8 are segregated in the matrix. The average tensile strength of the solder varies around 42 MPa. The bond with silicon is formed due to interaction of active titanium with the silicon surface at the formation of a reaction layer, composed of a new product, TiSi2. In the boundary of the Cu/solder an interaction between the liquid bismuth solder and the copper substrate occurs, supported by the eutectic reaction. The mutual solubility between the liquid bismuth solder is very limited, on both the Bi and the Cu side. The average shear strength in the case of a combined joint of Si/Cu fabricated with Bi11Ag1.5Ti solder is 43 MPa.