Currently, a large part of forest roads with a bituminous surface course constructed in the Czech Republic in the second half of the last century has been worn out. The aim of the study is to verify the possibility and the accuracy of the road wearing course damage detected by four different remote sensing methods: close range photogrammetry, terrestrial laser scanning, mobile laser scanning and airborne laser scanning. At the beginning of verification, cross sections of the road surface were surveyed geodetically and then compared with the cross sections created in the DTMs which were acquired using the four methods mentioned above. The differences calculated between particular models and geodetic measurements show that close range photogrammetry achieved an RMSE of 0.0110 m and the RMSE of terrestrial laser scanning was 0.0243 m. Based on these results, we can conclude that these two methods are sufficient for the monitoring of the asphalt wearing course of forest roads. These methods allow precise and objective localization, size and quantification of the road damage. By contrast, mobile laser scanning with an RMSE of 0.3167 m does not reach the required precision for the damage detection of forest roads due to the vegetation that affects the precision of the measurements. Similar results are achieved by airborne laser scanning, with an RMSE of 0.1392 m. As regards the time needed, close range photogrammetry appears to be the most appropriate method for damage detection of forest roads.

Currently, a large part of the forest roads that were built using the bituminous surface technology in the second half of the last century have been worn out. This means that forest owners and forest managers urgently need to determine the amount and extent of this damage and establish a suitable repair plan, which demands both time and staff. The aim of the study is to verify whether it is possible, and with what precision, to detect the damage of the wearing course by means of unmanned aerial systems, which would facilitate and accelerate this process and possibly make it cheaper. A 3D model of a forest road was created using photos of the current state of a damaged part of a forest road. The aerial photographs were taken by an unmanned aircraft. To verify the accuracy of the model, cross sections of the road surface were surveyed tachymetrically and compared with the cross sections created in the 3D model in ArcMap, from photogrammetric pointcloud using aerial photographs from the unmanned aircraft. The RMSE of the values of the control points in the 3D model cross sections compared to the values of the points in the tachymetric measurement of the cross sections reached to within 0.0198 m. The results of the tested road section showed that the unmanned aerial systems can be used to detect the forest road surface damage with the difference in accuracy being up to 2 cm compared with the accuracy of the current tachymetric methods. Based on the results we can conclude that the used method is appropriate for detailed monitoring of the condition of the asphalt wearing course of forest roads and allows for a precise and objective localization and quantification of damage.

The objective of the present paper is to confirm or reject the possible use of recycled asphalt to reinforce forest haul roads regarding the technical requirements set by the standards and directives relevant to the construction of forest road surfaces. The hypothesis is based on the presumption that recycled materials, if correctly used, can reach the same construction properties as standard materials, hence their application does not have a negative effect on reinforcement quality. On a selected stretch of forest road, three test sections were constructed with the use of recycled asphalt, however, each of them with a different technological solution. The first section was reinforced with unbound mixture – Type1 without added water, the second section was constructed using a version of vibrated macadam technology, and recycled asphalt was applied to the third section by the method of basic compacting. In each of the sections, tacheometric cross profile measurement was carried out at monthly intervals to monitor the changes in the cross profile shape, and the number of passages of fully loaded logging trucks was registered; static load tests were performed at pre-defined time intervals to determine the deformation moduli such as deformation characteristics of the road surface structural layers. In all three reinforcement versions, the values of deformation moduli observed during the static load tests were between 68–90 % of the values set by relevant standards for these technologies using natural aggregates. However, the tacheometric measurements did not reveal statistically significant changes in the shape of the reinforcement cross-section. Based on the obtained results, applying recycled asphalt to reinforce forest roads seems to be a suitable alternative to natural quarry aggregate used in unbound structural layers. Recycled material needs to meet the regulatory limits for foreign elements and pass ecotoxicity tests, which is evidenced by a certificate on material compliance issued by the test laboratory.

Forests make up 34.1% of the Czech Republic total area and forest roads account for nearly the same length (47,465 km) as all other roads administered by the state and its regions (55,738 km). Forest roads are not as intensively used as other roads. On the other hand, as logging trucks carry the maximum permitted load on roads and forests create a specific microclimate, forest roads are subject to rapid wear. A road wearing course is generally designed for 20 years of service and for a maximum damage level of 25% before they are supposed to be reconstructed. To ensure this life cycle is adhered to, more efficient, faster, and more flexible surface damage detection adaptable for forest environment is needed. As smartphones and their optical devices, i.e., new iPhones with LiDAR sensors, become more advanced, the option arises to perform laser scanning on road surfaces using smartphones applications. This work aimed to test this technology and its precision applicability to assessing damage to a forest wearing course and compare it with another hand-held personal laser scanner (PLShh), represented in this study by GeoSLAM ZEB Horizon scanner, and more precise terrestrial laser scanning (TLS) technology, represented in this study by Faro Focus 3D laser scanner, which have started to replace tacheometric wearing course damage surveying thanks to their greater precision. So, this study involved a comparison of three alternative laser scanning methods focused especially on these, which are implemented in new iPhones for tacheometric surveying. First, a Faro Focus 3D laser scanner was used for the TLS method. Second, the PLShh method was tested on a GeoSLAM ZEB Horizon scanner. Third, another PLShh method using an iPhone 13 Pro with applications 3D Scanner and Polycam was evaluated. If we are comparing positional height accuracy of PLShh to tacheometric surveying on reference cross position height coordinates, ZEB Horizon achieved devXY and devZ RMSE 0.108 m; 0.025 m; iPhone 13 Pro with 3D Scanner app devXY and devZ RMSE 0.185 m; 0.021 m, and with Polycam app devXY and devZ RMSE 0.31 m; 0.045. TLS achieved the best results with devXY RMSE 0.049 and devZ RMSE 0.0077. The results confirm that only the TLS scanner achieves precision values in height differences applicable for an assessment of forest road wearing course damage measurement comparable with tacheometric surveying. Surprisingly, comparing the PLShh scanners to the TLS technology, they achieved interesting results, comparing their transverse profiles and 3D objects as digital surface models (DSM) of the road to TLS in height position. In transverse profiles, ZEB Horizon achieved devZ RMSE 0.032 m; iPhone 13 Pro with 3D Scanner app devZ RMSE 0.017 m, and with Polycam app devZ RMSE 0.041 m compared to the TLS method measured using a Faro Focus 3D static laser scanner. Comparing forest road DSM to Faro Focus 3D, ZEB Horizon achieved devZ RMSE 0.028 m; iPhone 13 Pro with 3D Scanner app devZ RMSE 0.018 m and with Polycam devZ RMSE 0.041 m. These results in height differences show that the height accuracy of PLShh achieves precision, which is applicable to determining the current shape of forest road wearing course compared to the required roof shape gradient. However, further testing provided the insight that such a kind of PLShh measurement is still only possible to use for the identification of a transverse profile shape, as in length measurement the length error increases. All PLShh are able to capture the current shape of forest road cross profile, but still they cannot be used for any design or calculation of material measurement needed for wearing course repair.

The article deals with resilience and protection of critical information infrastructure elements. The elements affect rapid recovery of the system to its original state and the increase of resistance during the subsequent emergency events. The article also deals with sectoral and cross-sectional criteria for determining the critical information infrastructure elements, which are closely related to resilience and protection. Risk assessment has been conducted in the area of critical information infrastructure. Finally, amendments of the Czech Cyber Security Act have been mentioned.