Nitrate is a major source of the inorganic nitrogen taken up by the roots of plants. Nitrate sources are generally derived from inorganic minerals by an energy-consuming chemical process; as a result, the price of chemical fertilizers is gradually increasing year by year. NO3-N, generated from N2 using the plasma technique, is an alternative method of producing nitrate from the air. Therefore, in this research, we aimed to determine the efficiency of generating NO3-N using plasma-activated water (PAW) to replace nitrates from chemical fertilizer in a nutrient solution. Green oak lettuce (Lactuca sativa L.) was grown in a hydroponics system using the double-pot technique. The plants were supplied with three different nutrient solutions (based on Hoagland’s solution), i.e., T1, no nitrate in the nutrient solution (NO3− = 0); T2, using nitrate sourced from a commercial chemical fertilizer (normal nitrate); and T3, using a nitrate source generated using the pinhole plasma jet technique (plasma nitrate). The other macronutrients and micronutrients in each treatment were equally supplied. The results show that, at the harvested stage (21 days after the plants received treatment), the no-nitrate (T1) treatment provided lower growth and yields. Moreover, compared with the normal nitrate (T2) and plasma nitrate (T3), the results indicate that most growth and yields showed no statistical differences. In terms of nitrate accumulation within plants, it was found that the normal nitrate treatment (T2) had the highest levels of nitrate accumulation, in both the underground and aboveground parts of green oak lettuce. These results confirmed that plasma nitrate could be an alternative source of nitrate N which provided a safer way for the environment and human health in terms of nitrate accumulation. In addition, data related to the chemical analysis of free amino acid concentrations in each treatment are discussed in this research.

Plasma activated water (PAW) generated from pinhole plasma jet using gas mixtures of argon (Ar) and 2% oxygen (O2) was evaluated for pesticide degradation and microorganism decontamination (i.e., Escherichia coli and Colletotrichum gloeosporioides) in chili (Capsicum annuum L.). A flow rate of 10 L/min produced the highest concentration of hydrogen peroxide (H2O2) at 369 mg/L. Results showed that PAW treatment for 30 min and 60 min effectively degrades carbendazim and chlorpyrifos by about 57% and 54% in solution, respectively. In chili, carbendazim and chlorpyrifos were also decreased, to a major extent, by 80% and 65% after PAW treatment for 30 min and 60 min, respectively. E. coli populations were reduced by 1.18 Log CFU/mL and 2.8 Log CFU/g with PAW treatment for 60 min in suspension and chili, respectively. Moreover, 100% of inhibition of fungal spore germination was achieved with PAW treatment. Additionally, PAW treatment demonstrated significantly higher efficiency (p < 0.05) in controlling Anthracnose in chili by about 83% compared to other treatments.

This research was aimed at developing a dental prototype from 3D printing technology using a synthetic filament of polylactic acid (PLA) and zirconium dioxide (ZrO2) with glycerol and silane coupling agent as a binder. A face-centered central composite design was used to study the effects of the filament extrusion parameters and the 3D printing parameters. Tensile and compressive testing was conducted to determine the stress-strain relationship of the filaments. The yield strength, elongation percentage and Young’s modulus were also calculated. Results showed the melting temperature of 193 °C, ZrO2 ratio of 17 wt.% and 25 rpm screw speed contributed to the highest ultimate tensile strength of the synthetic filament. A Nozzle temperature of 210 °C and an infill density of 100% had the most effect on the ultimate compressive strength whilst the printing speed had no significant effects. Differential scanning calorimetry (DSC) was used to study the thermal properties and percentage of crystallinity of PLA filaments. The addition of glycerol and a silane coupling agent increased the tensile strength and filament size. The ZrO2 particles induced the crystallization of the PLA matrix. A higher crystallization was also obtained from the annealing treatment resulting in the greater thermal resistance performance of the dental crown prototype.

A severe plastic deformation process for the achievement of favorable mechanical properties for metallic powder is mechanical milling. However, to obtain the highest productivity while maintaining reasonable manufacturing costs, the process parameters must be optimized to achieve the best mechanical properties. This study involved the use of response surface methodology to optimize the mechanical milling process parameters of harmonic-structure pure Cu. Certain critical parameters that affect the properties and fracture mechanisms of harmonic-structure pure Cu were investigated and are discussed in detail. The Box–Behnken design was used to design the experiments to determine the correlation between the process parameters and mechanical properties. The results show that the parameters (rotation speed, mechanical milling time, and powder-to-ball ratio) affect the microstructure characteristics and influence the mechanical performance, including the fracture mechanisms of harmonic-structure pure Cu specimens. The best combination values of the ultimate tensile strength (UTS) and elongation were found to be 272 MPa and 46.85%, respectively. This combination of properties can be achieved by applying an optimum set of process parameters: a rotation speed of 200 rpm; mechanical milling time of 17.78 h; and powder-to-ball ratio of 0.065. The superior UTS and elongation of the harmonic-structure pure Cu were found to be related to the delay of void and crack initiation in the core and shell interface regions, which in turn were controlled by the degree of strength variation between these regions.

No abstract