There has been a tremendous amount of research in the past decade to optimize the mechanical properties and degradation behavior of the biodegradable Mg alloy for orthopedic implant. Despite the feasibility of degrading implant, the lack of fundamental understanding about biocompatibility and underlying bone formation mechanism is currently limiting the use in clinical applications. Herein, we report the result of long-term clinical study and systematic investigation of bone formation mechanism of the biodegradable Mg-5wt%Ca-1wt%Zn alloy implant through simultaneous observation of changes in element composition and crystallinity within degrading interface at hierarchical levels. Controlled degradation of Mg-5wt%Ca-1wt%Zn alloy results in the formation of biomimicking calcification matrix at the degrading interface to initiate the bone formation process. This process facilitates early bone healing and allows the complete replacement of biodegradable Mg implant by the new bone within 1 y of implantation, as demonstrated in 53 cases of successful long-term clinical study.biodegradable implant | bone formation | clinical application T he century-old concept of the fixation device that holds the fractured bones in place to allow repair through the natural bone remodeling process is still being practiced today without alteration (1-5). The recent rapid growth of the elderly demographic of physically active adults has tremendously intensified the occurrence of bone trauma cases, highlighting once again the major drawbacks of current surgical approaches and osteosynthesis systems, such as inevitable secondary surgery to remove the inert fixation devices after complete bone healing and inflammatory response due to the release of metal ions. In the past decade, countless studies have been performed to control and optimize the mechanical and corrosion properties of magnesium-based alloys (6-9), which, thanks to their degradation in the physiological environment, could overcome the limitations of inert implant materials and shift the paradigm of conventional bone fixation devices toward new horizons. Driven by these new possibilities, important findings regarding, among others, the degradation mechanism of Mg-based alloys (10, 11), the formation of corrosion protective layers by degradation products (12, 13), and the osteogenetic properties of Mg ions (14, 15) have been reported in the literature. However, such findings are based on the observation of degradation products and of bone healing at the macroscale level. Due to lack of fundamental understanding on biocompatibility and underlying bone formation mechanism of the degradation product, there is so far only one known case of statistically insignificant clinical study result (16) with a short-term follow-up. In our previous study, we reported successful development and long-term in vivo study of uniformly slowly degrading Mg-5wt%Ca-1wt%Zn alloy system (SI Appendix, Figs. S1 and S2) featuring adequate mechanical strength [ultimate tensile strength (UTS) ∼250 MPa] (17) a...

The limited grain size (<200 nm) for transition metal dichalcogenides (TMDs) grown by molecular beam epitaxy (MBE) reported in the literature thus far is unsuitable for high-performance device applications. In this work, the fundamental nucleation and growth behavior of WSe 2 is investigated through a detailed experimental design combined with on-lattice, diffusion-based first principles kinetic modeling to enable large area TMD growth. A three-stage adsorption-diffusion-attachment mechanism is identified and the adatom stage is revealed to play a significant role in the nucleation behavior. To limit the nucleation density and promote 2D layered growth, it is necessary to have a low metal flux in conjunction with an elevated substrate temperature. At the same time, providing a Serich environment further limits the formation of W-rich nuclei which suppresses vertical growth and promotes 2D growth. The fundamental understanding gained through this investigation has enabled an increase of over one order of magnitude in grain size for WSe 2 thus far, and provides valuable insight into improving the growth of other TMD compounds by MBE and other growth techniques such as chemical vapor deposition (CVD).

It was demonstrated that organolead halide perovskites (OHPs) show a resistive switching behavior with an ultralow electric field of a few kilovolts per centimeter. However, a slow switching time and relatively short endurance remain major obstacles for the realization of the next-generation memory. Here, we report a performance-enhanced OHP resistive switching device. To fabricate topologically and electronically improved OHP thin films, we added hydroiodic acid solution (for an additive) in the precursor solution of the OHP. With drastically improved morphology such as small grain size, low peak-to-valley depth, and precise thickness, the OHP thin films showed an excellent performance as insulating layers in Ag/CHNHPbI/Pt cells, with an endurance of over 10 cycles, a high on/off ratio of 10, and an operation speed of 640 μs and without electroforming. We suggest plausible resistive switching and conduction mechanisms with current-voltage characteristics measured at various temperatures and with different top electrodes and device structures. Beyond the extended endurance, highly flexible resistive switching devices with a minimum bending radius of 5 mm create opportunities for use in flexible and wearable electronic devices.

Crystalline Mg-based alloys with a distinct reduction in hydrogen evolution were prepared through both electrochemical and microstructural engineering of the constituent phases. The addition of Zn to Mg-Ca alloy modified the corrosion potentials of two constituent phases (Mg + Mg2Ca), which prevented the formation of a galvanic circuit and achieved a comparable corrosion rate to high purity Mg. Furthermore, effective grain refinement induced by the extrusion allowed the achievement of much lower corrosion rate than high purity Mg. Animal studies confirmed the large reduction in hydrogen evolution and revealed good tissue compatibility with increased bone deposition around the newly developed Mg alloy implants. Thus, high strength Mg-Ca-Zn alloys with medically acceptable corrosion rate were developed and showed great potential for use in a new generation of biodegradable implants.

Pt-based bimetallic nanoparticles have attracted significant attention as a promising replacement for expensive Pt nanoparticles. In the systematic design of bimetallic nanoparticles, it is important to understand their preferred atomic structures. However, compared with unary systems, alloy nanoparticles present more structural complexity with various compositional configurations, such as mixed-alloy, core-shell, and multishell structures. In this paper, we developed a unified empirical potential model for various Pt-based binary alloys, such as Pd-Pt, Cu-Pt, Au-Pt, and Ag-Pt. Within this framework, we performed a series of Monte Carlo (MC) simulations that quantify the energetically favorable atomic arrangements of Pt-based alloy nanoparticles: an intermetallic compound structure for the Pd-Pt alloy, an onion-like multi-shell structure for the Cu-Pt alloy, and core-shell structures (Au@Pt and Ag@Pt) for the Au-Pt and Ag-Pt alloys. The equilibrium nanoparticle structures for the four alloy types were compared with each other, and the structural features can be interpreted by the interplay of their material properties, such as the surface energy and heat of formation. PACS numbers: 61.46.+w, 36.40.Ei, 64.70.Nd I. II. INTERATOMIC POTENTIAL MODEL A. Embedded atom method potentials for Pt, Pd, and novel metals (Ag, Au, Cu)