Kava ( Piper methysticum Forst f., Piperaceae) has anxiolytic properties and the ability to promote a state of relaxation without the loss of mental alertness. The rapid growth of the nutraceutical market between 1998 and 2000 has been stopped by a ban in Europe and Australia because of some suspicion of liver toxicity. It is now important to develop a fast, cheap, and reliable quality test to control kava exports. The aim of this study is to develop a calibration of the near-infrared reflectance spectroscopy (NIRS) using partial least-squares (PLS) regression. Two hundred thirty-six samples of kava roots, stumps, and basal stems were collected from the Vanuatu Agricultural Research and Technical Centre germplasm collection and from four villages. These samples, representing 45 different varieties, were analyzed using NIRS to record their absorption spectra between 400 and 2500 nm. A set of 101 selected samples was analyzed for their kavalactone content using HPLC. The results were used for PLS calibration of the NIRS. The NIRS prediction of the kavalactone content and the dry matter were in agreement with the HPLC results. There were good correlations between these two series of results, and coefficients ( R (2)) were all close to 1. The measurements were reproducible and had repeatability on par with the HPLC method. The NIRS system has been calibrated for the six major kavalactone content measurements, and it is suggested that this method could be used for quality control in Vanuatu.

Genetic (different forms of puroindoline-b) and environment (through variations in vitreousness), have important effects on wheat grain mechanical properties. The two methods of hardness measurements (NIRS, SKCS) do not give the same information. Bread wheat near-isogenic lines differing in hardness, due to distinct puroindoline-b alleles (the wild type, Pinb-D1a, or the mutated forms, Pinb-D1b or Pinb-D1d), were grown for three years in seven sites and under two nitrogen fertilization levels, to study genetic and environmental effects on grain mechanical properties. Two methods, Near-Infrared Reflectance Spectroscopy (NIRS) and Single Kernel Characterization System (SKCS), currently used for grain hardness characterization, were carried out. Grain vitreousness, which is known to affect the grain mechanical behavior but is generally not studied, was also measured, as well as three other characters (Thousand Grain Weight, Test Weight and protein content). The relationships between the different characters were studied. Results revealed a clear effect of the different Pinb-D1 alleles on NIRS hardness, and a marked impact of the environmental conditions on vitreousness. SKCS hardness was influenced by both Pinb-D1 alleles and environmental conditions. The relationship between SKCS and NIRS hardness was strong when considering together soft and hard genotypes, but moderate within a class of genetical hardness. Vitreousness had only a weak effect on NIRS hardness, whereas vitreousness and SKCS values were strongly correlated, with two distinct regressions for soft and hard genotypes. Vitreousness was positively related to protein content, especially in the case of hard genotypes, which were able to reach high vitreousness values never observed for soft genotypes.

Genetic (Pinb-D1 alleles) and environment (through vitreousness) have important effects on bread wheat milling behavior. SKCS optimal values corresponding to soft vitreous or hard mealy grains were defined to obtain the highest total flour yield. Near-isogenic lines of bread wheat that differ in hardness, due to distinct puroindoline-b alleles (the wild type, Pinb-D1a, or the mutated forms, Pinb-D1b or Pinb-D1d), were grown in different environments and under two nitrogen fertilization levels, to study genetic and environmental effects on milling behavior. Milling tests used a prototype mill, equipped with two break steps, one sizing step, and two reduction steps, and this enabled 21 individual or aggregated milling fractions to be collected. Four current grain characters, thousand grain weight, test weight, grain diameter, and protein content, were measured, and three characters known to influence grain mechanical resistance, NIRS hardness, SKCS hardness index, and grain vitreousness (a character affecting the grain mechanical behavior but generally not studied). As expected, the wild type or mutated forms of Pinb-D1 alleles led to contrasted milling behavior: soft genotypes produced high quantities of break flour and low quantities of reduction flour, whereas reverse quantities were observed for hard genotypes. This different milling behavior had only a moderate influence on total flour production. NIRS hardness and vitreousness were, respectively, the most important and the second most important grain characters to explain milling behavior. However, contrary to NIRS hardness, vitreousness was only involved in endosperm reduction and not in the separation between the starchy endosperm and the outer layers. The highest flour yields were obtained for SKCS values comprised between 30 and 50, which corresponded either to soft vitreous or hard mealy grains. Prediction equations were defined and showed a good accuracy estimating break and reduction flours portions, but should be used more cautiously for total flour.

Differences in milling behavior among hard‐type common wheat (Triticum aestivum) cultivars are well known to millers. Among them, the French cultivar Soissons, which contains the Pinb‐D1d allelic form of the puroindoline b gene, is particularly distinguished for its high milling value. Near‐isogenic lines (NILs) differing by the allelic forms of the puroindoline b gene, Pinb‐D1d or Pinb‐D1b (one of the most frequent alleles found in the European wheat population), were constructed. Grain characteristics obtained after wheat cultivation in distinct environmental conditions were compared between NILs and the cultivar Soissons, as was their fractionation behavior. Results showed that NILs containing the Pinb‐D1d allele displayed lower values of grain hardness and vitreousness than did the corresponding lines containing the Pinb‐D1b allelic form under the same cultivation conditions. Both genetic background and environmental conditions appeared to affect grain texture. Measured single‐kernel characterization system hardness index values of the samples under study were found to be correlated with the vitreousness values. Studies of the milling behavior helped to point out that grain vitreousness is an important factor acting on endosperm breakage ability, whatever the genetic background of the wheat. Our results also demonstrated that, at similar levels of vitreousness, the endosperm of Soissons could more easily be reduced than that of other wheat lines.