Formamidinium tin iodide (FASnI3)-based perovskite solar cells (PSCs) have achieved significant progress in the past several years. However, these devices still suffer from low power conversion efficiency (PCE=6%) and poor stability. Recently, Cesium (Cs)-doped Formamidinium tin iodide (FA1−xCsxSnI3) showed enhanced air, thermal, and illumination stability of PSCs. Hence, in this work, FA1−xCsxSnI3 PSCs have been rigorously studied and compared to pure FASnI3 PSCs using a solar cell capacitance simulator (SCAPS) for the first time. The aim was to replace the conventional electron transport layer (ETL) TiO2 that reduces PSC stability under solar irradiation. Therefore, FA1−xCsxSnI3 PSCs with different Cs contents were analyzed with TiO2 and stable ZnOS as the ETLs. Perovskite light absorber parameters including Cs content, defect density, doping concentration and thickness, and the defect density at the interface were tuned to optimize the photovoltaic performance of the PSCs. The simulation results showed that the device efficiency was strongly governed by the ETL material, Cs content in the perovskite and its defect density. All the simulated devices with ZnOS ETL exhibited PCEs exceeding 20% when the defect density of the absorber layer was below 1015 cm−3, and deteriorated drastically at higher values. The optimized structure with FA75Cs25SnI3 as light absorber and ZnOS as ETL showed the highest PCE of 22% with an open circuit voltage Voc of 0.89 V, short-circuit current density Jsc of 31.4 mA·cm−2, and fill factor FF of 78.7%. Our results obtained from the first numerical simulation on Cs-doped FASnI3 could greatly increase its potential for practical production.

A hybrid tin-based perovskite solar cell with p-i-n inverted structure is modeled and simulated using SCAPS. The inverted structure is composed of PEDOT:PSS (as hole transport layer—HTL)/GA0.2FA0.78SnI3-1% EDAI2 (as perovskite absorber layer)/C60-fullerene (as electron transport layer—ETL). Previous experimental studies showed that unlike conventional tin-based perovskite solar cells (PSC), the present hybrid tin-based PSC passes all harsh standard tests and generates a power conversion efficiency of only 8.3%. Despite the high stability that this material exhibits, emphasis on enhancing its power conversion efficiency (PCE) is crucial. To that end, various ETL and HTL materials have been rigorously investigated. The impact of energy level alignment between HTL/absorber and absorber/ETL interfaces have been elucidated. Moreover, the thickness and the doping concentration of all the previously mentioned layers have been varied to inspect their effect on the photovoltaic performance of the PSC. The optimized structure with CuI (copper iodide) as HTL and ZnOS (zinc oxysulphide) as ETL scored a PCE of 26%, which is more than three times greater than the efficiency of the initial structure. The current numerical simulation on GA0.2FA0.78SnI3-1% EDAI2 could greatly increase its chance for commercial development.

When suspensions involving rigid rods become too concentrated, standard dilute theories fail to describe their behavior. Rich microstructures involving complex clusters are observed, and no model allows describing its kinematics and rheological effects. In previous works the authors propose a first attempt to describe such clusters from a micromechanical model, but neither its validity nor the rheological effects were addressed. Later, authors applied this model for fitting the rheological measurements in concentrated suspensions of carbon nanotubes (CNTs) by assuming a rheo-thinning behavior at the constitutive law level. However, three major issues were never addressed until now: (i) the validation of the micromechanical model by direct numerical simulation; (ii) the establishment of a general enough multi-scale kinetic theory description, taking into account interaction, diffusion and elastic effects; and (iii) proposing a numerical technique able to solve the kinetic theory description. This paper focuses on these three major issues, proving the validity of the micromechanical model, establishing a multi-scale kinetic theory description and, then, solving it by using an advanced and efficient separated representation of the cluster distribution function. These three aspects, never until now addressed in the past, constitute the main originality and the major contribution of the present paper.

No abstract

: Selected transcription factors have critical roles to play in organism survival by regulating the expression of genes that control the adaptations needed to handle stress conditions. The retinoblastoma (Rb) protein coupled with the E2F transcription factor family was demonstrated to have roles in controlling the cell cycle during freezing and associated environmental stresses (anoxia, dehydration). Rb phosphorylation or acetylation at different sites provide a mechanism for repressing cell proliferation that is under the control of E2F transcription factors in animals facing stresses that disrupt cellular energetics or cell volume controls. Other central regulators of the cell cycle including Cyclins, Cyclin dependent kinases (Cdks), and checkpoint proteins detect DNA damage or any improper replication, blocking further progression of cell cycle and interrupting cell proliferation. This review provides an insight into the molecular regulatory mechanisms of cell cycle control, focusing on Rb-E2F along with Cyclin-Cdk complexes typically involved in development and differentiation that need to be regulated in order to survive extreme cellular stress.