This article aims to study water-cooling effects on residual stress friction stir welding (FSW) of AA6068-T6 aluminum alloy. For this reason, the FSW and submerged FSW processes are simulated by computational fluid dynamic (CFD) method to study heat generation. The increment hole drilling technique was used to measure the residual stress of welded samples. The simulation results show that materials softening during the FSW process are more than submerged. This phenomenon caused the residual stress of the joint line in the submerged case to be lower than in the regular FSW joint. On the other hand, the results revealed that the maximum residual stresses in both cases are below the yielding strength of the AA6068-T6 aluminum alloy. The results indicated that the residual stress along the longitudinal direction of the joint line is much larger than the transverse direction in both samples.

The use of aluminum alloys, nowadays, is swiftly growing from the prerequisite of producing higher strength to weight ratio. Lightweight components are crucial interest in most manufacturing sectors, especially in transportation, aviation, maritime, automotive, and others. Traditional available joining methods have an adverse effect on joining these lightweight engineering materials, increasing needs for new environmentally friendly joining methods. Hence, friction stir welding (FSW) is introduced. Friction stir welding is a relatively new welding process that can produce high-quality weld joints with a lightweight and low joining cost with no waste. This paper endeavors to deals with optimizing process parameters for quality criteria on tensile and hardness strengths. Samples were taken from a 5 mm 6061-T6 aluminum alloy sheet with butt joint configuration. Controlled process parameters tool profile, rotational speed and transverse speed were utilized. The process parameters are optimized making use of the combination of Grey relation analysis method and L9 orthogonal array. Mechanical properties of the weld joints are examined through tensile, hardness, and liquid penetrant tests at room temperature. From this research, rotational speed and traverse speed become significant parameters at a 99% confidence interval, and the joint efficiency reached 91.3%.

No abstract

Low weight and high strength are significant factors in the current decade’s spread of composite sandwich materials. Previous studies have proven that forming stiffening ribs in these materials through the Single Point Incremental Forming (SPIF) process is possible and gives encouraging results. On the other hand, knowledge of residual stress (RS) values that form during the manufacturing process is essential, as they may affect the structural integrity of manufactured elements, whether in compression or tension. The investigation of the RS in the composite materials formed by the SPIF process using the XRD method was very limited in the previous studies, so this research aims to apply the X-ray diffraction (XRD) method to determine RS on the part of the LITECOR® sandwich material formed using SPIF. LITECOR® consists of a plastic core between two layers of steel. In this study, three types of LITECOR® were used with differing plastic core thicknesses of 0.8, 1.25, and 1.6 mm, while the steel layers’ thickness remained the same at 0.3 mm. The axial and traverse RSs were measured in five positions on both sides of the formed part. It was found that the achieved RSs varied from tensile to compressive along the formed regions. It was found that the residual stress values in both directions were inversely proportional to the thickness of the plastic core. It was noted that the highest RS values were in the unformed base metal, after which the RS was reduced on both sides of the SPIF-formed region, followed by a rise in the RS at the concave of the SPIF-formed region. The maximum measured RS for X-axes was 1041 MPa, whereas, for Y-axes, it was 1260 MPa, both of which were recorded on the back side at a thickness of t = 0.8 mm.

In this study, the effects of the traverse and rotational velocities of the noncontact shoulder tool on the heat generation and heated flux during the friction stir joining of high-density polyamide 6 (PA6) polymer were investigated. The computational fluid dynamics (CFD) method was employed to simulate the thermomechanical phenomena during the friction stir joining (FSJ) process of PA6. A developed model was used to consider the void formation and thermochemical properties of PA6. The surface and internal heat flow, material flow, and geometry of the joint were simulated, and an experimental study evaluated the simulation results. The simulation results indicated that the stir zone formed was smaller than regular joints with a noncontact shoulder tool. Despite the polymer’s traditional FSJ, heat generation and material flow do not differ significantly between advancing and retreating sides. On the other hand, the surface flow is not formed, and the surface temperature gradient is in a narrow line behind the tool. The material velocity increased at higher rotational speed and lower transverse velocity and in the stir zone with more giant geometry forms. The maximum generated heat was 204 °C, and the maximum material velocity was predicted at 0.44 m/s in the stir zone, achieved at 440 rpm and 40 mm/min tool velocities.