The aim of this study was to investigate transpiration and its main driving factors on the example of a hybrid poplar plantation with the clone Populus maximowiczii 9 P. nigra, cv. Max 1 on a site in the hilly loess region of Saxony (Germany). Transpiration was measured using sap flow techniques during the 2007 and 2008 growing season. At the same time, throughfall, soil moisture dynamics and soil physical properties were also measured. Total transpiration rates amounted to 486 mm and 463 mm, respectively, during the 2 years. Maximum daily transpiration rates reached 6.7 mm/day, while an average of 2.2 mm/day for the entire growing season was recorded. The main controlling factors for stand transpiration included the evaporative demand, water availability and soil temperature. The information was implemented into a simple empirical model for the prediction of transpiration. It can be concluded that large-scale establishment of poplar plantations will result in a distinct reduction in groundwater recharge. On the other hand, surface run-off and soil erosion may decrease. Due to limited water availability in the late growing season, the growth potential of the tested clone cannot fully be exploited at many sites in Germany.

Increasing temperatures and drought occurrences recently led to soil moisture depletion and increasing tree mortality. In the interest of sustainable forest management, the monitoring of forest soil properties will be of increasing importance in the future. Vis-NIR spectroscopy can be used as fast, non-destructive and cost-efficient method for soil parameter estimations. Microelectromechanical system devices (MEMS) have become available that are suitable for many application fields due to their low cost as well as their small size and weight. We investigated the performance of MEMS spectrometers in the visual and NIR range to estimate forest soil samples total C and N content of Ah and Oh horizons at the lab. The results were compared to a full-range device using PLSR and Cubist regression models at local (2.3 ha, n: Ah = 60, Oh = 50) and regional scale (State of Saxony, Germany, 184,000 km2, n: Ah = 186 and Oh = 176). For each sample, spectral reflectance was collected using MEMS spectrometer in the visual (Hamamatsu C12880MA) and NIR (NeoSpetrac SWS62231) range and using a conventional full range device (Veris Spectrophotometer). Both data sets were split into a calibration (70%) and a validation set (30%) to evaluate prediction power. Models were calibrated for Oh and Ah horizon separately for both data sets. Using the regional data, we also used a combination of both horizons. Our results show that MEMS devices are suitable for C and N prediction of forest topsoil on regional scale. On local scale, only models for the Ah horizon yielded sufficient results. We found moderate and good model results using MEMS devices for Ah horizons at local scale (R2≥ 0.71, RPIQ ≥ 2.41) using Cubist regression. At regional scale, we achieved moderate results for C and N content using data from MEMS devices in Oh (R2≥ 0.57, RPIQ ≥ 2.42) and Ah horizon (R2≥ 0.54, RPIQ ≥2.15). When combining Oh and Ah horizons, we achieved good prediction results using the MEMS sensors and Cubist (R2≥ 0.85, RPIQ ≥ 4.69). For the regional data, models using data derived by the Hamamatsu device in the visual range only were least precise. Combining visual and NIR data derived from MEMS spectrometers did in most cases improve the prediction accuracy. We directly compared our results to models based on data from a conventional full range device. Our results showed that the combination of both MEMS devices can compete with models based on full range spectrometers. MEMS approaches reached between 68% and 105% of the corresponding full ranges devices R2 values. Local models tended to be more accurate than regional approaches for the Ah horizon. Our results suggest that MEMS spectrometers are suitable for forest soil C and N content estimation. They can contribute to improved monitoring in the future as their small size and weight could make in situ measurements feasible.

No abstract

No abstract

Recently, forest management faces new challenges resulting from increasing temperatures and drought occurrences. For sustainable, site-specific management strategies, the availability of up to date soil information is crucial. Proximal soil sensing techniques are a promising approach for rapid and inexpensive collection of data, and could facilitate the provision of the necessary information. This study evaluates the potential of visual and near-infrared spectroscopy (vis-NIRS) for estimating soil parameters relevant for humus mapping in Saxon forests. Therefore, soil samples from the organic layer are included. So far there is little knowledge about the applicability of vis-NIRS in the humus layer of forests. We investigate the spectral behaviour of samples from organic (Oh) and mineral (0–5 cm, Ah) horizons, pointing out differences in the occurring absorption features. Further, we identify and assess the accuracy of selected soil properties based on vis-NIRS for forest sites, compare the outcome of different regression methods, investigate the implications for forest soils due to the presence and different composition of the humus layer and organic horizons and interpret the results regarding their usefulness for soil mapping and monitoring purposes. For this, we used retained humus soil samples of forests from Saxony. Regression models were built with Partial Least Squares Regression, Support Vector Machine and Cubist. Investigated properties were carbon (C) and nitrogen (N) content, C/N ratio, pH value, cation exchange capacity (CEC) and base saturation (BS) due to their importance for assessing humus conditions in forests. In organic Oh horizons, prediction results for C and N content achieved R² values between 0.44 and 0.58, with corresponding RPIQ ranging from 1.58 to 2.06 depending on the used algorithm. Estimations of C/N ratio were more precise with R² = 0.65 and RMSE = 2.16. Best results were reported for pH value, with R² = 0.90 and RMSE = 0.20. Regarding BS, the best model accuracy was R² = 0.71, with RMSE = 13.97. In mineral topsoil, C and N content models achieved higher values of R² = 0.59 to 0.72, with RPIQ values between 2.22 and 2.54. However, prediction accuracy was lower for C/N ratio (R² = 0.50, RMSE = 3.52) and pH values (R² = 0.62, RMSE = 0.29). Models for CEC achieved R² = 0.65, with RPIQ = 2.81. In general, prediction precision varied dependent on the used algorithm, without showing clear tendencies. Classification into pH classes was exemplified since this offers a new perspective for humus mapping on forest soils. Balanced accuracy for the defined classes ranged from 0.50 to 0.87. We show that vis-NIR spectroscopy is suitable for assessing humus conditions in Saxon forests (Germany), in particular not only for mineral horizons but also for organic Oh horizons.