Coupled magneto-optical imaging and local misorientation angle mapping have been used to demonstrate the percolative nature of supercurrent flow in YBa 2 Cu 3 O 7Ϫx ͑YBCO͒ coated conductors grown on deformation-textured Ni substrates. Barriers to current flow occur at many YBCO grain boundaries ͑GBs͒ which have propagated through the buffer layers from the underlying Ni substrate, and all Ni GBs with misorientation angles Ͼ4°initiate percolative current flow. This type of current barrier is characteristic of the conductor form and has been found to exist in samples with J c (0 T,77 K) values Ͼ2 MA/cm 2 . Sharpening of the local substrate texture or improving in low-angle GB properties should lead to higher J c values. © 2000 American Institute of Physics. ͓S0003-6951͑00͒00341-7͔High critical current density (J c ) conductors capable of operating in fields of several tesla at liquid-nitrogen temperature are critical to large-scale applications of hightemperature superconductors. Coated conductors ͑CCs͒ with biaxially textured YBa 2 Cu 3 O x ͑YBCO͒ respond to this need. [1][2][3] One widely employed approach today uses deformation texturing of a metal substrate, generally pure Ni, on which buffer layers and YBCO are grown. 1,2 Such architectures permit J c (0 T,77 K) values 1,2 Ͼ1 MA/cm 2 , but many samples have lower values. Here we couple magneto-optical imaging and local misorientation angle mapping to show that many such barriers to current flow occur at YBCO grain boundaries ͑GBs͒ which have propagated through the buffer layers from the Ni GBs in the underlying substrate. All Ni GBs with misorientation angles Ͼ4°were found to initiate percolative current flow. Since typical deformation-textured substrates have many GBs misoriented in the range of 5°-10°, this study shows that it will be very valuable for CC technology to further enhance substrate texture and/or to improve low-angle GB properties.Magneto-optical ͑MO͒ imaging, light microscopy, and backscattered electron Kikuchi pattern ͑BEKP͒ analysis of the local texture were conducted on a series of four CC samples grown on deformation-textured Ni substratres with in-plane and out-of-plane full width at half maxima of 6.6°-7.4°and 5.8°-8.7°, respectively, as measured by x-ray pole figures. The buffer and YBCO layers were deposited by pulsed-laser deposition ͑PLD͒ with architecture YBCO/CeO 2 /yttria-stabilized zirconia ͑YSZ͒/CeO 2 /Ni and thickness of 300-1200/100/500/100 nm for the respective oxide layers. The thickness of the YBCO layer varied from sample to sample without obvious differences in the properties measured by MO imaging and ac susceptibility. A 0.6-m-thick YBCO sample had a high transport J c (0 T,77 K) of 1.2 MA/cm 2 . The remaining samples were taken directly to other characterizations.A representative MO image of the granular fluxpenetration network obtained using standard imaging procedures 4,5 is shown in Fig. 1. This network is common to CCs with varying constructions from multiple sources. Among the variations are deformation-textured s...

The Nb-Si system offers a possibility of ductile-phase toughening of the brittle Nb5Si3 intermetallic with the terminal niobium-silicon solid solution. Powder composites have been made in which the volume fraction of the terminal Nb-Si phase is systematically varied in a matrix of Nb5Si3 in order to study the extent of toughening. The Nb-Si solid-solution phase was observed to exhibit cleavage failure under both as hot pressed and heat treated conditions, thereby limiting the toughening attained by the presence of this phase. Hot working of the composite results in a dramatic improvement in toughness because of a change in the plastic behavior and fracture mode of the terminal Nb-Si phase from brittle cleavage to a mixed mode of cleavage and ductile microvoid growth and coalescence (dimpled) fracture.

The public reporting burden for this collection of information is estimated to average 1 hour per response, including the time for reviewing instructions, searching existing data sources, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this bu den estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports (0704-0188), 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302. Respondents should be aware that notwithstanding any other provision of law no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number.