A new stationary phase for reversed-phase high performance liquid chromatography (RP HPLC) was created by coating spherical 3 μm carbon core particles in a layer-by-layer (LbL) fashion with poly(allylamine) (PAAm) and nanodiamond. Unfunctionalized core carbon particles were characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectrometry (ToF-SIMS), and Raman spectroscopy. After LbL of PAAm and nanodiamond, which yields ca. 4 μm core-shell particles, the particles were simultaneously functionalized and cross-linked using a mixture of 1,2-epoxyoctadecane and 1,2,7,8-diepoxyoctane to obtain a mechanically stable C(18)/C(8) bonded outer layer. Core-shell particles were characterized by SEM, and their surface area, pore diameter, and volume were determined using the Brunauer-Emmett-Teller (BET) method. Short stainless steel columns (30 × 4.6 mm i.d.) were packed and the corresponding van Deemter plots obtained. The Supporting Information contains a MATLAB program used to fit the van Deemter data. The retentions of a suite of analytes were investigated on a conventional HPLC at various organic solvent compositions, pH values of mobile phases, including extreme pH values, and column temperatures. At 60 °C, a chromatogram of 2,6-diisopropylphenol showed 71,500 plates/m (N/m). Chromatograms obtained under acidic conditions (pH 2.7) of a mixture of acetaminophen, diazepam, and 2,6-diisopropylphenol and a mixture of phenol, 4-methylphenol, 2-chlorophenol, 4-chlorophenol, 4-bromophenol, and 1-tert-butyl-4-methylphenol are presented. Retention of amitriptyline, cholesterol, and diazinon at temperatures ranging from 35 to 80 °C and at pH 11.3 is reported. A series of five basic drugs was also separated at this pH. The stationary phase exhibits considerable hydrolytic stability at high pH (11.3) and even pH 13 over extended periods of time. An analysis run on a UHPLC with a "sandwich" injection appeared to reduce extra column band broadening and gave best efficiencies of 110,000-120,000 N/m.

We report an efficient, general methodology for producing high-surface area metal oxide nanomaterials for a vast range of metal oxides, including at least one metal oxide nanomaterial from nearly every transition metal and semi-metal group in the periodic table (groups 3-4 and 6-15) as well as several from the lanthanide group (see ). The method requires only 2-3 simple steps; a hydrated metal salt (usually a nitrate or chloride salt) is ground with bicarbonate (usually NH4HCO3) for 10-30 minutes to form a precursor that is then either untreated or rinsed before being calcined at relatively low temperatures (220-550 °C) for 1-3 hours. The method is thus similar to surfactant-free aqueous methods such as co-precipitation but is unique in that no solvents are added. The resulting "solvent-deficient" environment has interesting and unique consequences, including increased crystallinity of the products over other aqueous methods and a mesoporous nature in the inevitable agglomerates. The products are chemically pure and phase pure with crystallites generally 3-30 nm in average size that aggregate into high surface area, mesoporous agglomerates 50-300 nm in size that would be useful for catalyst and gas sensing applications. The versatility of products and efficiency of the method lend its unique potential for improving the industrial viability of a broad family of useful metal oxide nanomaterials. In this paper, we outline the methodology of the solvent-deficient method using our understanding of its mechanism, and we describe the range and quality of nanomaterials it has produced thus far.

No abstract

No abstract

The structures of Al-modified anatase TiO 2 supports were analyzed using traditional analysis techniques of X-ray diffraction, transmission electron microscopy, and N 2 sorption as well as X-ray absorption near-edge spectroscopy, 27 Al magic-angle spinning NMR, and low-temperature heat capacity. The combined results from these characterizations reveal that the Al dopant is incorporated either on the surface or in vacancies depending on the details of the synthetic method used. Alumina incorporated on the surface stabilizes TiO 2 by lowering the surface energy of anatase and stabilizing planes with high surface energy that would otherwise join to achieve a reduced surface energy. On the other hand, Al incorporated in TiO 2 vacancies stabilizes the structure through increasing lattice strain and limiting mass transport necessary for grain growth. The 22 mol % Al-modified TiO 2 with Al on the surface had average crystallite diameter of 6 nm, surface area of 184 m 2 g −1 , pore volume of 0.34 cm 3 g −1 , and pore diameter of 6.4 nm compared with the 22 mol % Al-modified TiO 2 with Al incorporated in vacancies and on the surface which had average crystallite diameter of 2− 3 nm, surface area of 471 m 2 g −1 , pore volume of 0.44 cm 3 g −1 , and pore diameter of 4.4 nm. This work demonstrates the importance of structure analysis of doped nanomaterials in the development of stabilized catalysts and catalyst supports.