A novel liquid-phase exfoliation of layered crystals enables the production of defect-free and high quality 2D-crystal dispersions on a large scale.

Interface engineering of organic-inorganic halide perovskite solar cells (PSCs) plays a pivotal role in achieving high power conversion efficiency (PCE). In fact, perovskite photoactive layer needs to work synergistically with the other functional components of the cell, such as charge transporting/active buffer layers and electrodes. In this context, graphene and related twodimensional materials (GRMs) are promising candidates to tune "on demand" the interface properties of PSCs. In this work, we fully exploit the potential of GRMs by controlling the optoelectronic properties of hybrids between molybdenum disulfide (MoS2) and reduced graphene oxide (RGO) as hole transport layer (HTL) and active buffer layer (ABL) in mesoscopic methylammonium lead iodide (CH3NH3PbI3) perovskite (MAPbI3)-based PSC. We show that zero-dimensional MoS2 quantum dots (MoS2 QDs), derived by liquid phase exfoliated MoS2 flakes, provide both holeextraction and electron-blocking properties. In fact, on the one hand, intrinsic n-type doping-induced intra-band gap states effectively extract the holes through an electron injection mechanism. On the other hand, quantum confinement effects increase the optical band gap of MoS2 (from 1.4 eV for the flakes to > 3.2 for QDs), raising the minimum energy of its conduction band (from -4.3 eV for the flakes to -2.2 eV for QDs) above the one of conduction band of MAPbI3 (between -3.7 and -4 eV) and hindering electron collection. The van der Waals hybridization of MoS2 QDs with functionalized reduced graphene oxide (f-RGO), obtained by chemical silanization-induced linkage between RGO and (3-mercaptopropyl)trimethoxysilane, is effective to homogenize the deposition of HTLs or ABLs onto the perovskite film, since the two-dimensional (2D) nature of RGO effectively plug the pinholes of the MoS2 QDs films. Our "graphene interface engineering" (GIE) strategy based on van der Waals MoS2 QD/graphene hybrids enable MAPbI3-based PSCs to achieve PCE up to 20.12% (average PCE of 18.8%). The possibility to combine quantum and chemical effects into GIE, coupled with the recent success of graphene and GRMs as interfacial layer, represents a promising approach for the development of next-generation PSCs. Figure 1. (a) Sketch of mesoscopic MAPbI3-based PSC exploiting MoS2 QDs:f-RGO hybrids as both HTL and ABL. (b) Scheme of the energy band edge positions of the materials used in the different components of the assembled mesoscopic MAPbI3-based PSC. The energy band edge positions of MoS2 flakes and MoS2 QDs were determined from OAS and UPS measurements detailed along the text, while those of the other materials were taken from literature: FTO, 52 TiO2, 52 MAPbI3, 134-139 spiro-OMeTAD 52 and Au 52 . (c) State-of-the-art and predicted PCE evolution for PSCs, highlighting the synergistic potential of GIE and the formulation of advanced perovskite chemistries. The RGO flakes are effective to plug the pinholes MoS2 QDs films, thus to homogenize the HTL. The choice of the functionalization for RGO relies on the bifunctional r...

The miniaturization of energy storage units is pivotal for the development of next-generation portable electronic devices. Micro-supercapacitors (MSCs) hold great potential to work as on-chip micro-power sources and energy storage units complementing batteries and energy harvester systems. Scalable production of supercapacitor materials with costeffective and high-throughput processing methods is crucial for the widespread application of MSCs. Here, wet-jet milling exfoliation of graphite is reported to scale up the production of graphene as a supercapacitor material. The formulation of aqueous/alcohol-based graphene inks allows metal-free, flexible MSCs to be screen-printed. These MSCs exhibit areal capacitance (C areal ) values up to 1.324 mF cm −2 (5.296 mF cm −2 for a single electrode), corresponding to an outstanding volumetric capacitance (C vol ) of 0. 490 F cm −3 (1.961 F cm −3 for a single electrode). The screen-printed MSCs can operate up to a power density above 20 mW cm −2 at an energy density of 0.064 µWh cm −2 . The devices exhibit excellent cycling stability over chargedischarge cycling (10 000 cycles), bending cycling (100 cycles at a bending radius of 1 cm) and folding (up to angles of 180°). Moreover, ethylene vinyl acetate-encapsulated MSCs retain their electrochemical properties after a home-laundry cycle, providing waterproof and washable properties for prospective application in wearable electronics.

Two-dimensional transition metal-dichalcogenides are emerging as efficient and costeffective electrocatalysts for hydrogen evolution reaction (HER). However, only the edge sites of their trigonal prismatic phase show HER-electrocatalytic properties, while the basal plane, which is absent of defective/unsaturated sites, is inactive. Here, we tackle the key challenge that is increasing the number of electrocatalytic sites by designing and engineering heterostructures composed of single-/few-layer MoSe 2 flakes and carbon nanomaterials (graphene or single-wall carbon nanotubes (SWNTs)) produced by solution processing. The electrochemical coupling between the materials that comprise the heterostructure effectively enhances the HER-electrocatalytic activity of the native MoSe 2 flakes. The optimization of the mass loading of MoSe 2 flakes and their electrode assembly via monolithic heterostructure stacking provided a cathodic current density of 10mAcm -2 at overpotential of 100mV, a Tafel slope of 63mVdec -1 and an exchange current density (j 0 ) of 0.203µAcm -2 . In addition, electrode thermal annealing in a hydrogen environment and chemical bathing in nbutyllithium are exploited to texturize the basal planes of the MoSe 2 flakes (through Sevacancies creation) and to achieve in situ semiconducting-to-metallic phase conversion, respectively, thus they activate new HER-electrocatalytic sites. The as-engineered electrodes show a 4.8-fold enhancement of j 0 and a decrease in the Tafel slope to 54mVdec -1 .

Gallium selenide (GaSe) is a layered compound, which has been exploited in nonlinear optical applications and photodetectors due to its anisotropic structure and pseudodirect optical gap. Theoretical studies predict that its 2D form is a potential photocatalyst for water splitting reactions. Herein, the photoelectrochemical (PEC) characterization of GaSe nanoflakes (single‐/few‐layer flakes), produced via liquid phase exfoliation, for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in both acidic and alkaline media is reported. In 0.5 m H2SO4, the GaSe photoelectrodes display the best PEC performance, corresponding to a ratiometric power‐saved metric for HER (Φsaved,HER) of 0.09% and a ratiometric power‐saved metric for OER (Φsaved,OER) of 0.25%. When used as PEC‐type photodetectors, GaSe photoelectrodes show a responsivity of ≈0.16 A W−1 upon 455 nm illumination at a light intensity of 63.5 µW cm−2 and applied potential of −0.3 V versus reversible hydrogen electrode (RHE). Stability tests of GaSe photodetectors demonstrated a durable operation over tens of cathodic linear sweep voltammetry scans in 0.5 m H2SO4 for HER. In contrast, degradation of photoelectrodes occurred in both alkaline and anodic operation due to the highly oxidizing environment and O2‐induced (photo)oxidation effects. The results provide new insight into the PEC properties of GaSe nanoflakes for their exploitation in photoelectrocatalysis, PEC‐type photodetectors, and (bio)sensors.