Polyolefin is the most widely used and versatile commodity polymer. In this work, three types of polyolefin-based elastomers (PBEs) were adopted to toughen a high-flow polypropylene to improve its overall performance. The chain microstructures of these PBEs, including ethylene/1-octene (E/O) random copolymer from Dow Chemical s polyolefin elastomer (POE), olefin block copolymers (OBCs) of E/O from Dow, and ethylene/propylene random copolymer from ExxonMobil's propylene-based elastomer, were elucidated by GPC, 13 C NMR, TREF, and DSC techniques. The mechanical, thermal and optical properties, and morphology analysis of the PP/PBE blends were also studied to investigate the toughening mechanism of these PBEs. The results showed that all three types of PBEs can effectively improve the Izod impact strength of the PP/PBE blends by the addition of the rubber compositions, at the cost of the stiffness. PBE-1 and PBE-2 were found to have a great stiffness-toughness balance with about 1700 MPa of flexural modulus, about 110 • C of HDT and 3.6 kJ/m 2 of impact strength on the prepared PP/PBE blends by forming separated rubber phase and refined spherulite crystals. As a result, the OBC with alternating hard and soft segments could achieve a similar toughening effect as the E/P random copolymer. Surprisingly, no obvious rubber phase separation was observed in the PP/PBE-4 blend, which might be due to the good compatibility of the E/P random chains with the isotactic PP; therefore, the PP/PBE blend obtains great toughness performance and optical transparency with the highest Izod impact strength of 4.2 kJ/m 2 and excellent transparency. 22 million tons. Due to rapid market expansion of takeout for dining box and automobile industries in China, the high-flow homo polypropylene market has also witnessed a dramatic increase to about above 600 kilotons annually in the recent few years.Although the high-flow homo polypropylene with high melting index (typically above 50 g/10 min) and good processability possesses high flexural modulus, the impact strength is relatively low compared to the ethylene/propylene copolymer and easily suffers from brittle fracture [22]. In order to solve this problem, two approaches are typically adopted to improve the overall performance of the polymer. One alternative is to introduce an extra operation line for the incorporation of a small amount of ethylene into the isotactic chain in the PP production facility, and the other method is to make post-modifications of the high-flow polypropylene by blending elastomer with PP, and glass fibers for automobiles [23][24][25].The Polyolefin-based elastomers (PBEs) have received considerable attention because of their low density, recycling potential, better chemical resistance, processing advantages, and good resilience without permanent deformation. Unlike rubber, they do not require vulcanization. In addition, the low cost together with the wide availability of ethylene, propylene and α-olefin monomers makes the polyolefin-based elastomers more desirable. T...

No abstract

Summary: Facile and effective immobilization of late‐transition metal catalysts, 2,3‐bis‐(2,6‐diisopropylphenyl)butane diimine nickel(ii) dibromide (A) and 2,6‐bis‐[1‐(2,4,6‐trimethylphenylimino)ethyl]pyridine iron(ii) dichloride (B), for ethylene polymerization has been achieved, using spherical MgCl2 supports obtained by thermal dealcoholization of MgCl2 · 2.56C2H5OH instead of using supports of type MgCl2/AlRn(OEt)3−n. BET, XRD, IR, SEM, GPC, and DSC analyses indicate that the composition and structure of the supports, the activities of the supported catalysts, and the properties of the resultant polymers are strongly dependent on the dealcoholization temperature. The support SP‐3 obtained by treating MgCl2 · 2.56C2H5OH at 170 °C for 4 h is very effective for immobilizing late‐transition metal FeII and NiII catalysts. Compared with the corresponding unsupported homogeneous catalysts, a significant increase in activity is observed for the SP‐3 supported catalysts in ethylene polymerization, and the kinetics of polymerization is stable during the reaction process. In addition, replication of the support morphology is found in final polymers.Kinetic profiles of ethylene polymerization using SPC‐4, SPC‐5, and SPC‐6 under 1.0 MPa and at 70 °C.imageKinetic profiles of ethylene polymerization using SPC‐4, SPC‐5, and SPC‐6 under 1.0 MPa and at 70 °C.