This study compared the surface detail reproduction and dimensional accuracy of stone models obtained from molds disinfected with 2% sodium hypochlorite, 2% chlorhexidine digluconate or 0.2% peracetic acid to models produced using molds which were not disinfected, with 3 alginate materials (Cavex ColorChange, Hydrogum 5 and Jeltrate Plus). The molds were prepared over matrix containing 20-, 50-, and 75-µm lines, performed under pressure with perforated metal tray. The molds were removed following gelation and either disinfected (using one of the solutions by spraying followed by storage in closed jars for 15 min) or not disinfected. The samples were divided into 12 groups (n=5). Molds were filled with dental gypsum Durone IV and 1 h after the start of the stone mixing the models were separated from the tray. Surface detail reproduction and dimensional accuracy were evaluated using optical microscopy on the 50-µm line with 25 mm in length, in accordance with the ISO 1563 standard. The dimensional accuracy results (%) were subjected to ANOVA. The 50 µm-line was completely reproduced by all alginate impression materials regardless of the disinfection procedure. There was no statistically significant difference in the mean values of dimensional accuracy in combinations between disinfectant procedure and alginate impression material (p=0.2130) or for independent factors. The disinfectant solutions and alginate materials used in this study are no factors of choice regarding the surface detail reproduction and dimensional accuracy of stone models.

This study evaluated the effect of green tea application time on the bond strength of enamel after enamel bleaching. Enamel samples were obtained from 80 third molars and randomly divided into 7 experimental groups (G1-G7) and 1 group without treatment (G8): G1, bleached with 10% carbamide peroxide (CP); G2, CP + 10% sodium ascorbate gel (SA) for 15 min; G3, CP + SA for 30 min; G4, CP + SA for 60 min; G5, CP + 10% green tea gel (GT) for 15 min; G6, CP + GT for 30 min; G7, CP + GT for 60 min. The CP was applied onto the enamel surface for 8 h for 14 days. The SA was applied in groups 2, 3 and 4, and the GT was applied in groups 5-8 according to the above described application times. Immediately after treatment, the specimens were bonded with Adper Single Bond 2 and Filtek Z350XT. The specimens were prepared to microtensile bond strength analysis. Fracture mode analysis was performed using a stereoscopic loupe. The data were statistically analyzed by two-way analysis of variance, the Tukey's and Dunnett's tests (=5%). The means (standard deviation) were: G1, 23.3 (3.2); G2, 25.2 (3.9); G3, 26.4 (5.4); G4, 30.2 (4.5); G5, 26.6 (3.4); G6, 22.0 (5.4); G7, 31.4 (3.3); G8, 31.4 (3.2). All groups had a high percentage of adhesive failures. In conclusion, the bond strength values were higher than the value in the bleached group only when the antioxidants were applied for 60 min.

The objective of this study was to evaluate the antioxidant effect of green tea on microtensile bond strength (μTBS) to bleached enamel. Forty-two human third molars were randomly divided into six experimental groups (n = 7 each group): group 1, no treatment; group 2, bleaching (10% carbamide peroxide); group 3, bleaching + 10% sodium ascorbate gel (SA); group 4, bleaching + 10% green tea gel (GT); group 5, SA; and group 6, GT. In groups 2, 3, and 4, bleach was applied onto the enamel surface for 6 h, every day for 14 d. In groups 3 and 5, SA was applied for 1 h; and in groups 4 and 6, GT was applied for 1 h. Immediately after treatment, the specimens were bonded with Adper Single Bond 2 and Filtek Z350 XT. The μTBS of the specimens was tested using a universal testing machine. Fracture mode analysis of the bonded enamel surface was performed using scanning electron microscopy. The mean μTBS values for each group were: group 1, 33.2 ± 5.8 MPa; group 2, 22.6 ± 5.5 MPa; group 3, 30.0 ± 5.2 MPa; group 4, 31.6 ± 3.8 MPa; group 5, 29.1 ± 4.2 MPa; and group 6, 32.2 ± 4.5 MPa. All groups had a higher percentage of mixed failures. In conclusion, green tea can be used as an alternative antioxidant on bleached enamel before bonding procedures.

No abstract

No abstract