These complexes crystallize as the less common axial isomer and reach EC50 < 1.8 μM against HeLa cell lines.

In this work, we explored how solvents can affect olefin oxidation reactions catalyzed by MCM-bpy-Mo catalysts and whether their control can be made with those players. The results of this study demonstrated that polar and apolar aprotic solvents modulated the reactions in different ways. Experimental data showed that acetonitrile (aprotic polar) could largely hinder the reaction rate, whereas toluene (aprotic apolar) did not. In both cases, product selectivity at isoconversion was not affected. Further insights were obtained by means of neutron diffraction experiments, which confirmed the kinetic data and allowed for the proposal of a model based on substrate–solvent crosstalk by means of hydrogen bonding. In addition, the model was also validated in the ring-opening reaction (overoxidation) of styrene oxide to benzaldehyde, which progressed when toluene was the solvent (reaching 31% styrene oxide conversion) but was strongly hindered when acetonitrile was used instead (reaching only 7% conversion) due to the establishment of H-bonds in the latter. Although this model was confirmed and validated for olefin oxidation reactions, it can be envisaged that it may also be applied to other catalytic reaction systems where reaction control is critical, thereby widening its use.

Gathering clean energy from fuel feedstocks is of paramount significance in environmental science. In this area, desulfurization provides a valuable contribution by eliminating sulfur compounds from fuel feedstocks to ensure they can be used without emission of toxic sulfur oxides. MoO3 nanoparticles have been hydrothermally synthesized and used as efficient catalyst in the oxidative desulfurization (ODS) of methylphenyl and diphenyl sulfide using TBHP or H2O2 as oxidant. The catalyst showed an enhancement in the ODS process of the two substrates revealing influence on the reaction rate and product selectivity. Temperature and solvent influenced the conversion for the desired product as well. The activity of the catalyst was stable for at least 3 continuous catalytic cycles. Catalytic performance of MoO3 nanomaterial was comparable or better than other catalysts reported in the literature in terms of the sulfoxide or sulfone yield.

Three new complexes [Mo(η3-C3H5)Br(CO)2{iPrN=C(R)C5H4N}], where R = H (IMP = N-isopropyl 2-iminomethylpyridine), Me, and Ph, were synthesized and characterized, and were fluxional in solution. The most interesting feature was the presence, in the crystal structure of the IMP derivative, of the two main isomers (allyl and carbonyls exo), namely the equatorial isomer with the Br trans to the allyl and the equatorial with the Br trans to one carbonyl, the position trans to the allyl being occupied by the imine nitrogen atom. For the R = Me complex, the less common axial isomer was observed in the crystal. These complexes were immobilized in MCM-41 (MCM), following functionalization of the diimine ligands with Si(OEt)3, in order to study the catalytic activity in olefin epoxidation of similar complexes as homogeneous and heterogeneous catalysts. FTIR, 13C- and 29Si-NMR, elemental analysis, and adsorption isotherms showed that the complexes were covalently bound to the MCM walls. The epoxidation activity was very good in both catalysts for the cis-cyclooctene and cis-hex-3-en-1-ol, but modest for the other substrates tested, and no relevant differences were found between the complexes and the Mo-containing materials as catalysts.

In this work we explored how solvents can affect olefin oxidation reactions catalyzed by MCM-bpy-Mo catalysts and whether their control can be made with those players. The results of this study evidenced that polar and apolar aprotic solvents modulated the reactions in different ways. Experimental data showed that acetonitrile (aprotic polar) could hinder largely the reaction rate whereas toluene (aprotic apolar) did not. In both cases product selectivity at isoconversion was not affected. Further insights were obtained by means of neutron diffraction experiments, which confirmed the kinetic data allowing to propose a model based on substrate-solvent crosstalk by means of hydrogen bonding. In addition, the model was also validated in the ring-opening reaction (overoxidation) of styrene oxide towards benzaldehyde, which progressed when toluene was the solvent (reaching 31% styrene oxide conversion) but was strongly hindered when acetonitrile was used instead (reaching only 7% conversion), due to the establishment of H-bonds in the latter. Although this model was confirmed and validated for olefin oxidation reactions, it can be envisaged that it may also be applied to other catalytic reaction systems where reaction control is critical, while widening its use.