Due to the increasingly challenging carbon emission reduction targets, hydrogen-containing fuel combustion is gaining the energy community’s attention, as highlighted recently in the U.S. Department of Energy’s (DOE) Hydrogen Program Plan [1]. Though fundamental and applied research of hydrogen-containing fuels has been a topic of research for several decades, there are knowledge-gaps and unexplored fuel blend combustion characteristics at conditions relevant to modern gas turbine combustors. Hydrogen will be burned directly or as mixtures with natural gas (NG) and/or ammonia (NH3) in these devices. Fundamental research on the combustion of hydrogen (H2) containing fuels is still essential, especially to overcome or accurately predict challenges such as nitrogen oxides (NOx) reduction and flashback and develop fuel flexible combustors for a prosperous hydrogen economy. We focused our investigation on a natural gas and hydrogen mixture. Measurements of laminar burning velocity (LBV) are necessary for these fuels to understand their applicability in the turbines and other engines. In this study, the maximum rate of pressure rise and LBV of methane (CH4), CH4/H2, natural gas, and natural gas/H2 mixture were measured in synthetic air. The experimental conditions were at an initial pressure of 1 atm and an initial temperature of 300 K. A realistic natural gas composition from the field was used in this study and consisted of CH4 and other alkanes. The experimental data were compared with simulations carried out with detailed chemical kinetic mechanisms.

Clean energy generation is gaining significant attention from industries, academia, and governments across the globe. The Allam cycle is one such technology that has been under focus due to its efficiency, environmental friendliness, and economics. This is a direct-fired cycle operating at supercritical conditions using carbon dioxide as a working fluid. Fuel or oxidizer jet mixing with CO2 is a vital phenomenon that governs combustion efficiency, and it is not well understood for the Allam cycle conditions. This paper experimentally and computationally investigated the jet characteristics of a methane jet injected into a subcritical to supercritical carbon dioxide environment. A wide range of injection pressures and temperatures were targeted between subcritical to supercritical conditions. Unlike previous studies, the current work focused on injecting lower-density (methane) jets into higher-density (carbon dioxide) environments. Schlieren imaging and methane absorption measurements were simultaneously performed with a CMOS high-speed camera and a 3.39 μm infrared laser. Specifically, we looked at the classical injection parameter of jet spreading angle, which was classically established to be mainly a density ratio function. Here, the jet cone angle was obtained from the post-processed schlieren videos. The jet cone angle is a critical characteristic parameter that describes the entrainment rate in a jet; thus, it is a crucial parameter in understanding the nature of the jet. The laser measurements were only used as an additional check to confirm the entry time of methane into the chamber filled with carbon dioxide. Notably, this paper makes a detailed comparison between the jet cone angles of jets with a density ratio. The result showed that the classical correlations, such as Abramovich’s theory applied to submerged turbulent gas jets developed for low-density ratio jets, were unsuitable for higher-density ratio jets. It was also observed that the divergence angles were dependent not only on density ratio but also on other parameters such as pressure ratios and reduced pressures.

No abstract

Clean energy generation is gaining significant attention from industries, academia, and governments across the globe. The Allam cycle is one such technology that has been under focus due to its efficiency, environmental friendliness, and economics. This is a direct-fired cycle operating at supercritical conditions using carbon dioxide as a working fluid. Fuel or oxidizer jet mixing with CO2 is a vital phenomenon that governs combustion efficiency, and it is not well understood for the Allam cycle conditions. This paper experimentally investigated the jet characteristics of a methane jet injected into a subcritical to supercritical carbon dioxide environment. A wide range of injection pressures and temperatures were targeted between subcritical to supercritical conditions. Unlike previous studies, the current work focused on injecting lower-density (methane) jets into higher-density (carbon dioxide) environments. Schlieren imaging and methane absorption measurements were simultaneously performed with a CMOS high-speed camera and a 3.39 μm infrared laser. Specifically, we looked at the classical injection parameter of jet spreading angle, which was classically established to be mainly a density ratio function. Here, the jet cone angle was obtained from the postprocessed schlieren imaging. The jet cone angle is a critical characteristic parameter that describes the entrainment rate in a jet; thus, it is a crucial parameter in understanding the nature of the jet. The laser measurements were only used as an additional check to confirm the entry time of methane into the chamber filled with carbon dioxide. Notably, this paper makes a detailed comparison between the jet cone angles of jets with a density ratio. The result showed that the classical correlations, such as Abramovich's theory applied to submerged turbulent gas jets developed for low-density ratio jets, were unsuitable for higher-density ratio jets. It was also observed that the divergence angles were dependent not only on density ratio but also on other parameters such as pressure ratios and reduced pressures.

No abstract