The aim of the study was to assess the antibacterial efficacy of photon-initiated photoacoustic streaming (PIPS) using an Er:YAG laser and sonic-activated irrigation combined with QMiX irrigant or sodium hypochlorite against Enterococcus faecalis intracanal biofilm. Root canals of 91 human extracted single-canal teeth were instrumented, sterilized, contaminated with E. faecalis and incubated for 15 days. The infected teeth were then randomly distributed into six experimental groups: G1: PIPS/Er:YAG laser (wavelength 2940 nm, pulse energy 20 mJ, 15 Hz, pulse duration 50 μs, energy density 2.06 J/cm(2), 3 × 20 s) with the QMiX irrigant; G2: PIPS/Er:YAG laser-activated 2.5 % NaOCl; G3 sonic-activated irrigation (EndoActivator system) for 60 s with the QMiX irrigant; G4 sonic-activated irrigation for 60 s with 2.5 % NaOCl; G5 30-gauge needle irrigation with the QMiX irrigant; G6 30-gauge needle irrigation with 2.5 % NaOCl. The positive control group was rinsed with sterile saline solution. The root canals were sampled by flushing with saline solution at baseline and after the treatments, serially diluted and cultured. The number of bacteria in each canal was determined by plate count. The presence and the absence of E. faecalis in root canals were demonstrated by polymerase chain reaction (PCR), and the pattern of the bacteria colonization was visualized by scanning electron microscopy. There was significant reduction in the bacterial population for all groups (p < 0.001). The best antibacterial efficacy was recorded after sonic-activated irrigation with both NaOCl (99.999 %) and QMiX (99.999 %) and after PIPS with QMiX (99.999 %), which were more effective than conventional irrigation with NaOCl (99.998 %) and the PIPS with the NaOCl (99.966 %). Also, the PIPS with QMiX solution provided the highest number of sterile samples (five). There was no difference in the bacteria reduction between the active irrigation techniques, regardless of the irrigant used. Although the laser activation did not improve the antimicrobial action of the NaOCl nor QMiX, the fact that it generated the greatest number of sterile samples warrants further investigation.

Woodworkers' exposure to airborne particles is measured with different sampling techniques throughout the world. Due to a great number of exposure data obtained with different samplers, European countries have aimed over the last ten years to find a conversion factor for mass concentrations that would render these measurements comparable. Following the accepted EU standards and regulations, we replaced a 25 mm open-faced (OF) filter holder with an IOM head to determine woodworkers' exposure to inhalable dust and establish an IOM/OF sampler ratio that might serve as a reliable factor for converting the existing OF data to IOM dust mass concentration in the industrial environment. For this side-by-side sampling we used personal 25 mm OF (N=29) and IOM (N=29) sampling heads over eight working hours. The obtained IOM/OF ratios ranged between 0.7 and 2.3. However, mass concentrations obtained by IOM and OF samplers did not significantly differ. Our findings suggest that there is no need for conversion of the existing OF data for workers exposed to wood dust, provided that dust mass concentrations in the working environment range between 1 mg m-3 and 7 mg m-3. Future side-by-side measurements should also involve environments with low wood dust mass concentrations.

No abstract

The aim of this in vitro study was to compare the apical sealing ability of total fill bioceramic root repair material (BC-RRM) and mineral trioxide aggregate (MTA), regarding the retrograde preparation technique used: ultrasonic or erbium, chromium: yttrium, scandium, gallium, or garnet (Er,Cr:YSGG) laser. The study sample consisted of 48 human single-rooted teeth. After root-end resection, the samples were divided into two groups, according to the retrograde preparation technique used: Group 1: ultrasonic; Group 2: Er,Cr:YSGG laser. In each group, half of the retrograde cavities were filled with BC-RRM, and the other half were filled with MTA. The specimens were mounted in tubes and sterilized in plasma. The root canals were inoculated with Enterococcus faecalis, and the tubes were filled with fetal bovine serum, leaving the apical part of the root in the serum. After 30 days, the canals were sampled and cultured, and the colony forming units (CFUs) were counted with the additional polymerase chain reaction (PCR analysis). There was no significant difference between ultrasonic groups and the Er,Cr:YSGG-MTA group, regarding the number of CFUs (p > 0.05). The Er,Cr:YSGG-BC-RRM group showed the highest number of remaining viable bacteria (p < 0.001). Both filling materials filled in ultrasonic preparations presented similar sealing abilities. The BC-RRM showed more leakage when used in retro cavities prepared with the Er,Cr:YSGG laser.

Wood processing is usually performed in environments with large amounts of endotoxin-rich bioaerosols that are associated with a variety of health effects. The aim of this preliminary study was to assess the relation between endotoxin levels in settled and airborne dust in wood-processing industry. Ten pairs of airborne and settled dust samples were collected in a sawmill and parquet manufacture of two wood-processing plants in Croatia. Endotoxin was assayed with a chromogenic end-point LAL (Limulus amebocyte lysate) method. The results showed that endotoxin levels in airborne respirable dust were above the proposed occupational exposure limit of 125 EU m -3 and could be considered hazardous for the respiratory system. In settled dust they ranged between 229.7 EU mg -1 and 604.3 EU mg -1 and in airborne dust between 166.8 EU mg -1 and 671.6 EU m -3 , but there was no signifi cant correlation between them (Spearman's rho=0.358, P=0.310). This study points to sawmill settled dust as endotoxin reservoir and suggests that it may add to already high exposure to airborne endotoxins associated with wood processing. Investigations of the relation between settled and airborne endotoxin levels should be continued to better understand the sources and sites of endotoxin contamination in wood-processing industry.