Recently about 90% of radiographs have been taken by the digital radiographic system in Japan, but the exposure dose of the patients are about ten-times different among the systems. We understood it by a surveytaken in 2007. We studied the visual evaluation with varying exposure doses using the image phantom of the lumber AP, lumber lateral and hip AP. Additionally we measured quantum efficiency (DQE) of the digital systems. We also studied the exposure index (EI) of IEC standard to see whether it is able to be the sensitivity index among the digital systems. DQE in 1.0 cycle/mm of CR, FPD (GOS), FPD (CsI, a-Se) became 0.2-0.25, 0.3, 0.5, respectively. Our results display that the dose reduction is relative to DQE. The visual evaluation results also show that dose reduction is possible among the systems. From these results, we are able to reduce the exposure dose of the patients at the clinical site. We also suggest that we manage the exposure dose using the E.I of the IEC standard.

Sub-second multidetector-row computed tomography systems provide great potential for the further improvement of CT coronary angiography (CTCA). However, because the temporal resolution (TR) of such CT systems is insufficient, blurring and artifacts produced by fast cardiac motion remain as unresolved issues. Previous TR investigations of CTCA were based on the retrospective electrocardiogram-gated multisegment reconstruction technique. However, the results obtained may not necessarily be correct because the TR of multisegment reconstruction may not be substantial due to the insufficient periodicity of cardiac motion. The optimal TR required for better CTCA images was evaluated with use of a dual-source CT system, which has various substantial TR modes (83, 125, and 165 ms). CTCA images of 147 patients with heart rates (HRs) ranging from 36 to 117 beats/minute (bpm) were evaluated visually on a 4-point scale. Our results revealed not only that the 165-ms TR is sufficient for low HRs (≤60 bpm), but also that the 83- and 125-ms TRs are unnecessary for such HRs. The image quality with the 125-ms TR mode was acceptable for the left anterior descending artery, left circumflex artery, and right coronary artery at low to intermediate HRs (≤70 bpm). At high HRs (>70 bpm), the 83-ms TR mode resulted in an excellent image quality for all cases except those with very rapid RCA motion. Adequate TRs for a wide range of heart rates (52-106 bpm) are thus clarified.

The edge method adopted by the International Electrotechnical Commission (IEC) for presampled modulation transfer function (presampled MTF) measurement has the advantage that the complexity and limitations of image acquisition are less than those of the slit method. On the other hand, it has the disadvantage that the maintenance of accuracy is difficult because of the noise amplification caused by the differentiation. In order to reduce this disadvantage, we proposed an effective method in which many edge profiles are synthesized and then the synthesized edge profiles are bound into regular interval bins. Furthermore, the influences of some factors in edge profile analysis on measurement accuracy were examined. The appropriate width of one bin was 10-20% of the sampling interval. Measurement error of the inclination angle of the edge should be made up to 0.05 degrees . The range of the angle was allowed to be from 1 to 5 degrees. If these conditions were fulfilled, accurate measurement up to the Nyquist frequency (fn) was possible. Using an actual computed radiography (CR) system, the presampled MTF was obtained by the slit method and our edge method. The two results showed good agreement.

The noise power spectrum (NPS) measurement is important for assessing noise properties of digital radiography systems, and its measurement method was standardized in International Electrotechnical Commission 62220-1 (IEC). However, improvement of its accuracy is not easy due to random data analysis. In this study, regarding error factors in the NPS measurement using 2-dimensional (2D) Fast Fourier transform, we investigated effects of overlap of region of interests (ROIs), number of average lines in 2D frequency space, directional dependence of frequency property, and detrending techniques. If the number of average lines was set so as to obtain a similar frequency range to IEC, total matrix size was the most important factor and error rate was decreased with increasing of the size. For images, including many trends, detrending using 256 x 256-pixels ROI and second-order polynomial fitting was the most effective. Consistent with the previous report, the overlap of ROIs was not effective for improving accuracy. Contrary to the previous report that indicated effectiveness of 128 x 128-pixels ROI for detrending, we demonstrated less affectivity of the ROI size, other than 256 x 256-pixels.

We devised a new noise filtering method to reduce the noise in the line spread function (LSF) for presampled modulation transfer function (MTF) analysis with the edge method. A filter was designed to reduce noise effectively by using a position-dependent filter controlled by the boundary frequency b for low-pass filtering, which is calculated