Abstract:JET underwent a transformation from a full carbon-dominated tokamak to a full metallic device with the ITER-like wall combination for the activated phase with Beryllium main chamber and Tungsten divertor. The ITER-Like Wall (ILW) experiment at JET provides an ideal test bed for ITER and shall demonstrate as primary goals the plasma compatibility with metallic walls and the reduction in fuel retention. We report on a set of experiments ( = 2.0 , = 2.0 − 2.4 , = 0.2 − 0.4) in different confinement and plasma conditions with global gas balance analysis demonstrating a strong reduction of the long term retention rate by a factor ten with respect to carbon references. All experiments have been executed in a series of identical plasma discharges in order to achieve maximum plasma duration until the analysis limit of the active gas handling system has been reached. The composition analysis shows high purity of the recovered gas, typically 99% D. For typical L-mode discharges ( = 0.5 ), type III ( = 5.0 ), and type I ELMy H-mode plasmas ( = 12.0 ) a drop of the retention rate normalised to the operational time in divertor configuration has been measured from 1.27 × 10 has been obtained with the ILW. The observed reduction by one order of magnitude confirms the expected predictions concerning the plasma-facing material change in ITER and widens the operation without active cleaning in the DT phase in comparison to a full carbon device.

No abstract

Disruptions are a major operational concern for next generation tokamaks, including ITER. They may generate excessive heat loads on plasma facing components, large electromagnetic forces in the machine structures and several MA of multi-MeV runaway electrons. A more complete understanding of the runaway generation processes and methods to suppress them is necessary to ensure safe and reliable operation of future tokamaks. Runaway electrons were studied at JET-ILW showing that their generation dependencies (accelerating electric field, avalanche critical field, toroidal field, MHD fluctuations) are in agreement with current theories.

The original goals of the JET ITER-like wall included the study of the impact of an all W divertor on plasma operation (Coenen et al 2013 Nucl. Fusion 53 073043) and fuel retention (Brezinsek et al 2013 Nucl. Fusion 53 083023). ITER has recently decided to install a full-tungsten (W) divertor from the start of operations. One of the key inputs required in support of this decision was the study of the possibility of W melting and melt splashing during transients. Damage of this type can lead to modifications of surface topology which could lead to higher disruption frequency or compromise subsequent plasma operation. Although every effort will be made to avoid leading edges, ITER plasma stored energies are sufficient that transients can drive shallow melting on the top surfaces of components. JET is able to produce ELMs large enough to allow access to transient melting in a regime of relevance to ITER. Transient W melt experiments were performed in JET using a dedicated divertor module and a sequence of IP = 3.0 MA/BT = 2.9 T H-mode pulses with an input power of PIN = 23 MW, a stored energy of ∼6 MJ and regular type I ELMs at ΔWELM = 0.3 MJ and fELM ∼ 30 Hz. By moving the outer strike point onto a dedicated leading edge in the W divertor the base temperature was raised within ∼1 s to a level allowing transient, ELM-driven melting during the subsequent 0.5 s. Such ELMs (δW ∼ 300 kJ per ELM) are comparable to mitigated ELMs expected in ITER (Pitts et al 2011 J. Nucl. Mater. 415 (Suppl.) S957–64). Although significant material losses in terms of ejections into the plasma were not observed, there is indirect evidence that some small droplets (∼80 µm) were released. Almost 1 mm (∼6 mm3) of W was moved by ∼150 ELMs within 7 subsequent discharges. The impact on the main plasma parameters was minor and no disruptions occurred. The W-melt gradually moved along the leading edge towards the high-field side, driven by j × B forces. The evaporation rate determined from spectroscopy is 100 times less than expected from steady state melting and is thus consistent only with transient melting during the individual ELMs. Analysis of IR data and spectroscopy together with modelling using the MEMOS code Bazylev et al 2009 J. Nucl. Mater. 390–391 810–13 point to transient melting as the main process. 3D MEMOS simulations on the consequences of multiple ELMs on damage of tungsten castellated armour have been performed. These experiments provide the first experimental evidence for the absence of significant melt splashing at transient events resembling mitigated ELMs on ITER and establish a key experimental benchmark for the MEMOS code.

No abstract