Optical solitons are waveforms that preserve their shape while propagating, relying on a balance of dispersion and nonlinearity [1,2]. Soliton-based data transmission schemes were investigated in the 1980s, promising to overcome the limitations imposed by dispersion of optical fibers. These approaches, however, were eventually abandoned in favor of wavelength-division multiplexing (WDM) schemes that are easier to implement and offer improved scalability to higher data rates. Here, we show that solitons may experience a comeback in optical communications, this time not as a competitor, but as a key element of massively parallel WDM. Instead of encoding data on the soliton itself, we exploit continuously circulating dissipative Kerr solitons (DKS) in a microresonator [3,4]. DKS are generated in an integrated silicon nitride microresonator [5] by four-photon interactions mediated by Kerr nonlinearity, leading to low-noise, spectrally smooth and broadband optical frequency combs [6]. In our experiments, we use two interleaved soliton Kerr combs to trans-mit a data stream of more than 50 Tbit/s on a total of 179 individual optical carriers that span the entire telecommunication C and L bands. Equally important, we demonstrate coherent detection of a WDM data stream by using a pair of microresonator Kerr soliton combs one as a multi-wavelength light source at the transmitter, and another one as a corresponding local oscillator (LO) at the receiver. This approach exploits the scalability advantages of microresonator soliton comb sources for massively parallel optical communications both at the transmitter and receiver side. Taken together, the results prove the significant potential of these sources to replace arrays of continuous-wave lasers in high-speed communications. In combination with advanced spatial multiplexing schemes [7,8] and highly integrated silicon photonic circuits [9], DKS combs may bring chip-scale petabit/s transceivers into reach.The first observation of solitons in optical fibers [2] in 1980 was immediately followed by major research efforts to harness such waveforms for long-haul communications [1]. In these schemes, data was encoded on soliton pulses by simple amplitude modulation using on-off-keying (OOK). However, even though the viability of the approach was experimentally demonstrated by transmission over one million kilometres [10], the vision of soliton-based communications was ultimately hindered by difficulties in achieving shape-preserving propagation in real transmission systems [1] and by the fact that nonlinear interactions intrinsically prevent dense packing of soliton pulses in either the time or frequency domain. Moreover, with the advent of wavelength-division multiplexing (WDM), line rates in long-haul communication systems could be increased by rather simple parallel transmission of data streams with lower symbol rates, which are less dispersion sensitive. Consequently, soliton-based communication schemes have moved out of focus over the last two decades. More recently, frequ...

Light detection and ranging is widely used in science and industry. Over the past decade, optical frequency combs were shown to offer advantages in optical ranging, enabling fast distance acquisition with high accuracy. Driven by emerging high-volume applications such as industrial sensing, drone navigation, or autonomous driving, there is now a growing demand for compact ranging systems. Here, we show that soliton Kerr comb generation in integrated silicon nitride microresonators provides a route to high-performance chip-scale ranging systems. We demonstrate dual-comb distance measurements with Allan deviations down to 12 nanometers at averaging times of 13 microseconds along with ultrafast ranging at acquisition rates of 100 megahertz, allowing for in-flight sampling of gun projectiles moving at 150 meters per second. Combining integrated soliton-comb ranging systems with chip-scale nanophotonic phased arrays could enable compact ultrafast ranging systems for emerging mass applications.

Demonstrating improved confinement of energetic ions is one of the key goals of the Wendelstein 7-X (W7-X) stellarator. In the past campaigns, measuring confined fast ions has proven to be challenging. Future deuterium campaigns would open up the option of using fusion-produced neutrons to indirectly observe confined fast ions. There are two neutron populations: 2.45 MeV neutrons from thermonuclear and beam-target fusion, and 14.1 MeV neutrons from DT reactions between tritium fusion products and bulk deuterium. The 14.1 MeV neutron signal can be measured using a scintillating fiber neutron detector, whereas the overall neutron rate is monitored by common radiation safety detectors, for instance fission chambers. The fusion rates are dependent on the slowing-down distribution of the deuterium and tritium ions, which in turn depend on the magnetic configuration via fast ion orbits. In this work, we investigate the effect of magnetic configuration on neutron production rates in W7-X. The neutral beam injection, beam and triton slowing-down distributions, and the fusion reactivity are simulated with the ASCOT suite of codes. The results indicate that the magnetic configuration has only a small effect on the production of 2.45 MeV neutrons from DD fusion and, particularly, on the 14.1 MeV neutron production rates. Despite triton losses of up to 50 %, the amount of 14.1 MeV neutrons produced might be sufficient for a time-resolved detection using a scintillating fiber detector, although only in high-performance discharges.

After completing the main construction phase of Wendelstein 7-X (W7-X) and successfully commissioning the device, first plasma operation started at the end of 2015. Integral commissioning of plasma start-up and operation using electron cyclotron resonance heating (ECRH) and an extensive set of plasma diagnostics have been completed, allowing initial physics studies during the first operational campaign. Both in helium and hydrogen, plasma breakdown was easily achieved. Gaining experience with plasma vessel conditioning, discharge lengths could be extended gradually. Eventually, discharges lasted up to 6 s, reaching an injected energy of 4 MJ, which is twice the limit originally agreed for the limiter configuration employed during the first operational campaign. At power levels of 4 MW central electron densities reached 3  ×  1019 m−3, central electron temperatures reached values of 7 keV and ion temperatures reached just above 2 keV. Important physics studies during this first operational phase include a first assessment of power balance and energy confinement, ECRH power deposition experiments, 2nd harmonic O-mode ECRH using multi-pass absorption, and current drive experiments using electron cyclotron current drive. As in many plasma discharges the electron temperature exceeds the ion temperature significantly, these plasmas are governed by core electron root confinement showing a strong positive electric field in the plasma centre.

Chip-scale integration of electronics and photonics is recognized as important to the future of information technology, as is the exploitation of the best properties of electronics, photonics, and plasmonics to achieve this objective. However, significant challenges exist including matching the sizes of electronic and photonic circuits; achieving low-loss transition between electronics, photonics, and plasmonics; and developing and integrating new materials. This review focuses on a hybrid material approach illustrating the importance of both chemical and engineering concepts. Silicon–organic hybrid (SOH) and plasmonic–organic hybrid (POH) technologies have permitted dramatic improvements in electro-optic (EO) performance relevant to both digital and analog signal processing. For example, the voltage–length product of devices has been reduced to less than 40 Vμm, facilitating device footprints of <20 μm2 operating with digital voltage levels to frequencies above 170 GHz. Energy efficiency has been improved to around a femtojoule/bit. This improvement has been realized through exploitation of field enhancements permitted by new device architectures and through theory-guided improvements in organic electro-optic (OEO) materials. Multiscale theory efforts have permitted quantitative simulation of the dependence of OEO activity on chromophore structure and associated intermolecular interactions. This has led to new classes of OEO materials, including materials of reduced dimensionality and neat (pure) chromophore materials that can be electrically poled. Theoretical simulations have helped elucidate the observed dependence of device performance on nanoscopic waveguide dimensions, reflecting the importance of material interfaces. The demonstration and explanation of the dependence of in-device electro-optic activity, voltage–length product, and optical insertion loss on device architecture (e.g., slot width) suggest new paradigms for further dramatic improvement of performance.