The quality of the monomers lactic acid and lactide as well as the chemical changes induced during polymerization and processing are crucial parameters for controlling the properties of the resulting poly(lactic acid) (PLA) products. This review presents the most important analysis and characterization methods for quality assessment of PLA and its precursors. The impurities typically present in lactic acid or lactide monomers and their possible origins and effects on resulting PLA products are discussed. The significance of the analyses for the different polymer production stages is considered, and special applications of the methods for studying features specific for PLA-based materials are highlighted.

Poly-l-lactide/poly-d-lactide (PLLA/PDLA) stereocomplex had much higher hydrolytic stability compared to plain PLLA, but at the same time shorter and more acidic degradation products were formed. Both materials were subjected to hydrolytic degradation in water and in phosphate buffer at 37 and 60 degrees C, and the degradation processes were monitored by following mass loss, water uptake, thermal properties, surface changes, and pH of the aging medium. The degradation product patterns were determined by electrospray ionization-mass spectrometry (ESI-MS). The high crystallinity and strong secondary interactions in the stereocomplex prevented water uptake and resulted in lower mass loss and degradation rate. However, somewhat surprisingly, the pH of the aging medium decreased much faster in the case of PLLA/PDLA stereocomplex. In accordance, the ESI-MS results showed that hydrolysis of PLLA/PDLA resulted in shorter and more acidic degradation products. This could be explained by the increased intermolecular crystallization due to stereocomplexation, which results in an increased number of tie chains. Because mainly these short tie chains are susceptible to hydrolysis this leads to formation of shorter oligomers compared to hydrolysis of regular PLLA.

Poly(lactic acid) (PLA) stereocomplexes have high potential as renewable materials for advanced polymer applications, mainly due to their high melting temperature (Tm, typically 230–240°C). The properties of PLA stereocomplexes consisting of linear high molar mass homopolymers have been studied extensively in the past, but the available information about the possibilities to affect the thermal properties of the stereocomplex by varying the structure of the blend components has not been sufficient. Novel stereocomplexes containing linear or star‐shaped D‐lactic acid (D‐LA) oligomers and high molar mass poly(L‐lactide) (L‐PLA) were thus prepared. The Tm and melting enthalpy (ΔHm) of the racemic crystallites were found to depend strongly on both the blending ratio and the arm‐length of the D‐lactic acid oligomer. The preparation method of the oligomers, i.e. step‐growth polymerization or ring‐opening polymerization (ROP), did not affect the Tm or ΔHm of the blends significantly. Slightly higher ΔHm values were, however, obtained, when linear oligomers were used. The results thus indicated that the Tm and ΔHm of PLA stereocomplexes could be optimized, simply by selecting a D‐LA oligomer having a suitable arm‐length and structure as the other blend component. The possibility to adjust the melting behavior of the stereocomplex blend is a significant advantage and could make PLA suitable for a wider range of products used at elevated temperatures. Copyright © 2010 John Wiley & Sons, Ltd.

Stereocomplexation of poly(L-lactide) (PLLA) with star shaped D-lactic acid (D-LA) oligomers with different architectures and end-groups clearly altered the degradation rate and affected the degradation product patterns. Altogether, nine materials were studied: standard PLLA and eight blends of PLLA with either 30 or 50 wt % of four different D-LA oligomers. The influence of several factors, including temperature, degradation time, and amount and type of D-LA oligomer, on the hydrolytic degradation process was investigated using a fractional factorial experimental design. Stereocomplexes containing star shaped D-LA oligomers with four alcoholic end-groups underwent a rather slow hydrolytic degradation with low release of degradation products. Materials with linear D-LA oligomers exhibited similar mass loss but released higher concentrations of shorter acidic degradation products. Increasing the fraction of D-LA oligomers with a linear structure or with four alcoholic end-groups resulted in slower mass loss due to higher degree of stereocomplexation. The opposite results were obtained after addition of D-LA oligomers with carboxylic chain-ends. These materials demonstrated lower degree of stereocomplexation and larger mass and molar mass loss, and also the release of degradation products increased. Increasing the number of alcoholic chain-ends from four to six decreased the degree of stereocomplexation, leading to faster mass loss. The degree of stereocomplexation and degradation rate were customized by changing the architecture and end-groups of the D-LA oligomers.

We have used phase-separated poly(3-hexyltiophene) (P3HT)/poly(L-lactic acid) (PLLA) blends to fabricate low-voltage ion-modulated transistors on a rough paper substrate. The semiconductor and insulator are mixed together in a solution and spin casted onto the paper substrate. Owing to their different solubilities and surface energies the P3HT and PLLA will phase separate vertically during the spinning process creating a thin layer of semiconductor on top of the insulator. This thin semiconductor layer, difficult to achieve by other means on an absorbing paper substrate, creates faster ion-modulated transistors. Using this approach we have created ring-oscillators on paper oscillating at 5 Hz.