Purpose of Review Fractures of osteoporotic bone in elderly individuals need special attention. This manuscript reviews the current strategies to provide sufficient fracture fixation stability with a particular focus on fractures that frequently occur in elderly individuals with osteoporosis and require full load-bearing capacity, i.e., pelvis, hip, ankle, and peri-implant fractures. Recent Findings Elderly individuals benefit immensely from immediate mobilization after fracture and thus require stable fracture fixation that allows immediate post-operative weight-bearing. However, osteoporotic bone has decreased holding capacity for metallic implants and is thus associated with a considerable fracture fixation failure rate both short term and long term. Modern implant technologies with dedicated modifications provide sufficient mechanical stability to allow immediate weight-bearing for elderly individuals. Depending on fracture location and fracture severity, various options are available to reinforce or augment standard fracture fixation systems. Summary Correct application of the basic principles of fracture fixation and the use of modern implant technologies enables mechanically stable fracture fixation that allows early weight-bearing and results in timely fracture healing even in patients with osteoporosis.

Purpose Valgus malalignment of the distal femur may be treated with corrective osteotomy. The purpose of this study was to compare the primary stability of a lateral opening‐wedge osteotomy (LOWO) using a uniplanar compared to a biplanar technique. A study was carried out to test both surgeries, with both an intact medial cortex and with a deliberate attached cut of the medial cortex simulating a fracture. The primary hypothesis was that the biplanar technique provides higher axial and torsional stiffness. It was further hypothesized that the mechanical superiority of the biplanar technique would not be affected in the case of breakage of the far medial cortex. Methods A LOWO was performed in ten synthetic femora (#3406 left large Femur, 4th Generation, Sawbones, Malmö, Sweden) using a lateral angle stable locking plate (NCB© Distal Femur Plate, Zimmer Biomet, Warsaw, USA). A uniplanar osteotomy was performed in five femora, and a biplanar osteotomy was performed in five femora. The femora were tested for axial and torsional loads using a servo‐hydraulic testing machine (Instron 8874, Instron Structural Testing GmbH, High Wycombe, UK). Results Axial stiffness decreased significantly (p = 0.001) in both groups (20% in the uniplanar group and 28 % in the biplanar group) by cutting the medial cortex. The type of osteotomy had no significant effect. A slightly lower but not statistically significant axial stiffness was seen in the biplanar group both for intact and broken medial cortices. Internal torsional stiffness dropped by more than 30% for the uniplanar group and almost 24% for the biplanar group when the cortex was cut (p < 0.001). No significant change concerning internal torsional stiffness was found between the two groups. External torsional stiffness decreased by 32% for the uniplanar group and 4% for the biplanar group after the cortical cut (p = 0.029). No significant change concerning external torsional stiffness was found between the groups, but the biplanar group showed a tendency towards higher values of external torsional stiffness. Conclusions The axial and torsional stiffness of the implant‐bone construct were not significantly affected by the type of osteotomy performed. Biplanar osteotomy tended to increase external torsional stiffness. In cases of fracture of the medial cortex, biplanar osteotomy significantly reduced the external rotation at the osteotomy and showed a significantly increased external torsional stiffness.

No abstract

Aims Evaluate if treating an unstable femoral neck fracture with a locking plate and spring-loaded telescoping screw system would improve construct stability compared to gold standard treatment methods. Methods A 31B2 Pauwels’ type III osteotomy with additional posterior wedge was cut into 30 fresh-frozen femur cadavers implanted with either: three cannulated screws in an inverted triangle configuration (CS), a sliding hip screw and anti-rotation screw (SHS), or a locking plate system with spring-loaded telescoping screws (LP). Dynamic cyclic compressive testing representative of walking with increasing weight-bearing was applied until failure was observed. Loss of fracture reduction was recorded using a high-resolution optical motion tracking system. Results LP constructs demonstrated the highest mean values for initial stiffness and failure load. LP and SHS constructs survived on mean over 50% more cycles and to loads 450 N higher than CS. During the early stages of cyclic loading, mean varus collapse of the femoral head was 0.5° (SD 0.8°) for LP, 0.7° (SD 0.7°) for SHS, and 1.9° (SD 2.3°) for CS (p = 0.071). At 30,000 cycles (1,050 N) mean femoral neck shortening was 1.8 mm (SD 1.9) for LP, 2.0 mm (SD 0.9) for SHS, and 3.2 mm (SD 2.5) for CS (p = 0.262). Mean leg shortening at construct failure was 4.9 mm (SD 2.7) for LP, 8.9 mm (SD 3.2) for SHS, and 7.0 mm (SD 4.3) for CS (p = 0.046). Conclusion Use of the LP system provided similar (hip screw) or better (cannulated screws) biomechanical performance as the current gold standard methods suggesting that the LP system could be a promising alternative for the treatment of unstable fractures of the femoral neck. Cite this article: Bone Joint Res 2020;9(6):314–321.