a b s t r a c tAntimicrobial packaging materials were obtained by incorporation of lysozyme into cellulose acetate (CA) films. In order to achieve controlled release of lysozyme, the structure of the films was changed from highly asymmetric and porous to dense by modulating the composition of the initial casting solution. The highest release rate, soluble lysozyme activity and antimicrobial activity were obtained with the film prepared from 5% CA solution including 1.5% lysozyme. Increasing CA content in the casting solution decreased the porosity of the films, hence, reduced the release rate, maximum released lysozyme activities and the antimicrobial activities of the films. In contrast, immobilized lysozyme activities and the tensile strength of the films increased. The incorporation of lysozyme did not cause significant reductions in tensile strength and elongation at break values except in films prepared with 15% CA. This study showed the good potential of asymmetric CA films to achieve controlled release in antimicrobial packaging.

In this study, interactions of polyethylene glycol (PEG)-coated gold nanoparticles (AuNPs) with cells were investigated with particular focus on the relationship between the PEG layer properties (conformation, grafting density, and hydrodynamic volume) and cell cycle arrest, apoptosis, and DNA damage. Steric hindrance and PEG hydrodynamic volume controlled the protein adsorption, whereas the AuNP core size and PEG hydrodynamic volume were primary factors for cell uptake and viability. At all PEG grafting densities, the particles caused significant cell cycle arrest and DNA damage against CaCo2 and PC3 cells without apoptosis. However, at a particular PEG grafting density (∼0.65 chains/ nm 2 ), none of these severe damages were observed on 3T3 cells indicating discriminating behavior of the healthy (3T3) and cancer (PC3 and CaCo2) cells. It was concluded that the PEG grafting density and hydrodynamic volume, tuned with the PEG concentration and AuNP size, played an important role in particle−cell interactions.

a b s t r a c tIn this study, whey protein isolate (WPI) based bio-nanocomposite films embedded with zein nanoparticles (ZNP) were prepared by solution casting. Nanoparticles were coated with sodium caseinate to obtain a uniform distribution in the films. The mechanical, water vapor barrier, surface wetting, morphological and viscoelastic properties of the films were investigated. The addition of ZNP significantly improved the water vapor barrier and mechanical properties of the WPI without adversely affecting the elongation of the films. Dynamical mechanical analysis and contact angle measurements revealed that upon addition of the nanoparticles, the fractional free volume and hydrophilicity of the WPI films decreased. Sodium caseinate containing both hydrophilic and hydrophobic groups created an efficient interface between the hydrophobic ZNP and hydrophilic WPI matrix, allowing for a homogeneous distribution of nanoparticles even at very high loading levels as evidenced by the scanning electron microscope (SEM) and atomic force microscopy (AFM) images. The WPI/ZNP nanocomposite films can potentially become effective food packaging materials.

a b s t r a c tAn innovative hydrophilic and anti-fouling coating material for application in membrane technology for wastewater treatment has been developed by polymerization of a polymerizable bicontinuous microemulsion (PBM) and used for surface modification of a commercial flat polyethersulfone (PES) membrane. The novel nanostructured coating has been produced using acryloyloxyundecyltriethylammonium bromide (AUTEAB) as a co-polymerizable surfactant, obtained through a synthetic method characterized by a lower cost and a higher reproducibility compared to other known polymerizable surfactants. The novel composite membranes have been characterized and compared with the uncoated PES membranes. Coated membranes resulted in a smoother surface and a higher hydrophilicity with respect to the uncoated ones, and showed a particular nano-size channel-like morphology making them highly resistant to the fouling phenomenon. The covalent anchorage of the surfactant on the membrane surface ensured the embedment of the molecule in the polymeric matrix avoiding its leaching and also leading the coated membranes to have significant antimicrobial activity, which is very important for reducing the biofouling phenomenon.All these aspects make the tailored coating material an ideal and efficient coating for modifications of commercial membrane surfaces, to be used in membrane processes in wastewater treatment.

This manuscript focuses on the effect of microstructure and mechanical properties of gelatin-based 3D conduits on the transdifferentiation of mesenchymal stem cells to Schwann cell-like phenotypes. This work builds on our recently accepted manuscript in Acta Biomaterialia focused on multifunctional 2D films, and focuses on 3D microstructured conduits designed to overcome limitations of current strategies to facilitate peripheral nerve regeneration. The comparison between conduits fabricated with nanofibrous, macroporous and ladder-like microstructures showed that the ladder-like conduits showed the most favorable environment for MSC transdifferentiation to Schwann-cell like phenotypes, as seen by both immunolabeling as well as secretion of neurotrophic factors. This work demonstrates the importance of controlling the 3D microstructure to facilitate tissue engineering strategies involving stem cells that can serve as promising approaches for peripheral nerve regeneration.