We review the rational choice, the analysis, the depletion and the properties imparted by the liquid layer in liquid-infused surfaces – a new class of low-adhesion surface.

A new family of polymeric, lubricant-infused, nanostructured wrinkled surfaces was designed that effectively retains inert nontoxic silicone oil, after draining by spin-coating and vigorous shear for 2 weeks. The wrinkled surfaces were fabricated using three different polymers (Teflon AF, polystyrene, and poly(4-vinylpyridine)) and two shrinkable substrates (Polyshrink and shrinkwrap), and Teflon on Polyshrink was found to be the most effective system. The volume of trapped lubricant was quantified by adding Nile red to the silicone oil before infusion and then extracting the oil and Nile red from the surfaces in heptane and measuring by fluorimetry. Higher volumes of lubricant induced lower roll-off angles for water droplets, and in turn induced better antifouling performance. The infused surfaces displayed stability in seawater and inhibited growth of Pseudoalteromonas spp. bacteria up to 99%, with as little as 0.9 μL cm of the silicone oil infused. Field tests in the waters of Sydney Harbor over 7 weeks showed that silicone oil infusion inhibited the attachment of algae, but the algal attachment increased as the silicone oil was slowly depleted over time. The infused wrinkled surfaces have high transparency and are moldable, making them suited to protect the windows of underwater sensors and cameras.

Slippery liquid infused porous surfaces (SLIPS) have recently gained a lot of attention because of their wide range of applications. We recently showed that SLIPS with most of their surface depleted of lubricant, as little lubricant as 0.02 ± 0.01 μL cm, were effective against marine biofouling. Characterization of the depletion and configuration of the immobilized liquid layer on SLIPS is crucial to optimizing their performance. Previous attempts at mapping lubricant thickness have been diffraction limited or indirectly measured thickness. Here, we use atomic force microscopy meniscus force measurements to directly map lubricant thickness with nanoscale resolution on wrinkled surfaces made from Teflon and poly(4-vinylpyridine) (P4VP). Using this method, we show that SLIPS are easily depleted and are effectively heterogeneous surfaces, where the majority of the surface is a thick lubricating layer stabilized by capillary forces and part nanothin layer stabilized long-range intermolecular forces. We found that the depleted silicone oil thickness on the tops of nonwettable (Teflon) wrinkles is approx. 5 nm, close to but greater than the minimum measurable thickness of approx. 3 nm. The silicone oil thickness on the tops of wettable (P4VP) wrinkles is approx. 15 nm. Surfaces in this state still show antibiofouling properties and thus show that a thick lubricating layer is not necessary for all favorable properties of SLIPS.

Lubricant-infused surfaces hold promise to reduce the huge frictional drag that slows down the flow of fluids at microscales. We show that infused Teflon wrinkled surfaces induce an effective slip length 50 times larger than expected based on the presence of the lubricant alone. This effect is particularly striking as it occurs even when the infused lubricant’s viscosity is several times higher than that of the flowing liquid. Crucially, the slip length increases with increasing air content in the water but is much higher than expected even in degassed and plain Milli-Q water. Imaging directly the immersed interface using a mapping technique based on atomic force microscopy meniscus force measurements reveals that the mechanism responsible for this huge slip is the nucleation of surface nanobubbles. Using a numerical model and the height and distribution of these surface nanobubbles, we can quantitatively explain the large fluid slip observed in these surfaces.

Lubricant-infused surfaces (LIS) have emerged as an innovative way to combat several modern challenges such as biofouling, ice formation and surface drag. The favourable properties of LIS are dependent on the presence and distribution of a lubricant layer coating the underlying substrate. Unfortunately, this layer is not stable indefinitely and will deplete due to external forces. Here, we study how an air/water interface depletes lubricant from LIS as a function of lubricant wettability on the substrate by varying the chemistry of both the lubricant and the substrate. The lubricants on the substrate deplete faster due to their dewetting into droplets. We also find that lubricants which spread onto the air/water interface are more susceptible to depletion. Finally, we investigate the effect of repeated immersions on the properties of liquid-like PDMS chains tethered to glass and find that dynamic contact angles on these surfaces remain constant over several dips and therefore their low hysteresis is unlikely due to unbound polymer.