Multitechnique characterization of six technical lignins including nuclear magnetic resonance and size exclusion chromatography studies.

Lignin is an attractive material for the production of renewable chemicals, materials and energy. However, utilization is hampered by its highly complex and variable chemical structure, which requires an extensive suite of analytical instruments to characterize. Here, we demonstrate that straightforward attenuated total reflection (ATR)‐FTIR analysis combined with principle component analysis (PCA) and partial least squares (PLS) modelling can provide remarkable insight into the structure of technical lignins, giving quantitative results that are comparable to standard gel‐permeation chromatography (GPC) and 2D heteronuclear single quantum coherence (HSQC) NMR methods. First, a calibration set of 54 different technical (fractionated) lignin samples, covering kraft, soda and organosolv processes, were prepared and analyzed using traditional GPC and NMR methods, as well as by readily accessible ATR‐FTIR spectroscopy. PLS models correlating the ATR‐FTIR spectra of the broad set of lignins with GPC and NMR measurements were found to have excellent coefficients of determination ( R 2 Cal.>0.85) for molecular weight ( M n , M w ) and inter‐unit abundances (β‐ O ‐4, β‐5 and β‐β), with low relative errors (6.2–14 %) as estimated from cross‐validation results. PLS analysis of a second set of 28 samples containing exclusively (fractionated) kraft lignins showed further improved prediction ability, with relative errors of 3.8–13 %, and the resulting model could predict the structural characteristics of an independent validation set of lignins with good accuracy. The results highlight the potential utility of this methodology for streamlining and expediting the often complex and time consuming technical lignin characterization process.

Lignin is an attractive renewable feedstock for aromatic bulk and fine chemicals production, provided that suitable depolymerization procedures are developed. Here, we describe a tandem catalysis strategy for ether linkage cleavage within lignin, involving ether hydrolysis by water‐tolerant Lewis acids followed by aldehyde decarbonylation by a Rh complex. In situ decarbonylation of the reactive aldehydes limits loss of monomers by recondensation, a major issue in acid‐catalyzed lignin depolymerization. Rate of hydrolysis and decarbonylation were matched using lignin model compounds, allowing the method to be successfully applied to softwood, hardwood, and herbaceous dioxasolv lignins, as well as poplar sawdust, to give the anticipated decarbonylation products and, rather surprisingly, 4‐(1‐propenyl)phenols. Promisingly, product selectivity can be tuned by variation of the Lewis‐acid strength and lignin source.

Lewis acids have been studied as catalysts in the organosolv treatment of wheat straw. Fractionation of the lignocellulosic biomass and fragmentation of lignin have been performed in aqueous ethanol in the presence of FeCl 2 , CuCl 2 , FeCl 3 , Ga(OTf) 3 , ZrOCl 2 or Sc(OTf) 3. The lignins were characterised in terms of molecular weight, ␤ O 4 linkage content and chemical functions through size exclusion chromatography; thioacidolysis; 31 P and 13 C NMR spectroscopies. The degree of delignification and the yield of Klason lignin increased with the hardness of the Lewis acid. About half of the delignification products were water-soluble monomers and oligomers. The nature of the Lewis acid influenced also the characteristics of the precipitated lignins. The molecular mass, the amount of OH groups and of aliphatic C O bonds decreased as cation hardness increased.

Lignin and humins are both (by-)products of biorefining processes aimed at the valorization of lignocellulosic biomass. In order to improve the efficiency of such biorefineries and to develop new valorization pathways for these polymeric materials, detailed insight into their complex chemical structure and functional group distribution is required. Here, we report on the quantification and classification of the ketone and aldehyde carbonyl functional groups contained in these two polymers by 19 F NMR. The known method of carbonyl derivatization with 4-(trifluoromethyl)phenylhydrazine to the corresponding hydrazone has been improved and simplified, allowing derivatization directly in an NMR tube, requiring no additional workup before quantification by 19 F NMR. Furthermore, the scope of the method was assessed and expanded, with model compound studies, which included monomeric and dimeric compounds as well as synthetic polymers, showing that the carbonyl functions can indeed be reproducibly quantified. Using this model compound library, the carbonyl functional groups in two technical lignins (Indulin Kraft and Alcell) and, for the first time, an industrial humin could be quantified and classified. The industrial humin was found to contain 6.6 wt % of carbonyl functions, with aliphatic and conjugated carbonyls being detected. The relatively high abundance of such functional groups, which are amenable to further chemical modification, provides opportunities for the use of these humin byproducts in various applications, e.g., as materials after derivatization.