Studies of diesel system deposits continue to be the subject of interest and publications worldwide. The introduction of high pressure common rail systems resulting in high fuel temperatures in the system with the concomitant use of fuels of varying solubilizing ability (e.g. ULSD and FAME blends) have seen deposits formed at the tip of the injector and on various internal injector components. Though deposit control additives (DCAs) have been successfully deployed to mitigate the deposit formation, work is still required to understand the nature and composition of these deposits. The study of both tip and internal diesel injector deposits (IDID) has seen the development of a number of bench techniques in an attempt to mimic field injector deposits in the laboratory. One of the most used of these is the Jet Fuel Thermal Oxidation Tester or JFTOT (ASTM D3241). The tester was originally designed to assess the oxidation of jet fuel, based on the principle that low stability fuels produce deposits that form on metal surfaces. Recently it has been modified so that under suitable conditions it may be used to determine the deposit forming potential of diesel fuels. The JFTOT technique has been used by a number of groups to try and understand diesel injector deposits. The ineradicable nature of the material on the JFTOT tube has seen the deposits analyzed by laser scanning microscopy, ellipsometry and recently infra-red microscopy. Other methods have been invasive involving either solvent washing or scraping off the deposit. In this paper other techniques for the analysis of deposits will be described yielding both chemical and metrological characteristics of the deposits. Fourier Transform Infrared Microscopy (FTIRM), and Time-of-Flight Secondary Ion Mass Spectrometry (ToFSIMS) will be used to describe the surface characteristics. Measurements from a Profile meter will be used to estimate deposit surface roughness and data from Scanning Electron Microscopy (SEM) will be employed to describe the morphology. The final techniques described will be Direct Analysis In Real Time Mass Spectrometry (DARTMS) using ambient mass spectrometry. and Fourier Transform Ion Cyclotron Resonance Mass spectrometry (FTICRMS) The advantage of the DART method is that mixtures and objects can be subjected to mass spectrometric analysis with the minimum of pre-treatment and sample preparation. Thus the technique is well suited for analyzing deposits on JFTOT tubes as it requires little sample preparation. A number of studies of materials deposited on JFTOT tubes will be described showing the suitability of these techniques for analyzing and providing the potential characterization of JFTOT deposits. The FTICRMS will be used to assign species in the JFTOT test fuels both pre and post test.
No abstract
Over the last decade, there has been an impetus in the automobile industry to develop new diesel injector systems, driven by a desire to reduce fuel consumption and proscribed by the requirement to fulfil legislation emissions. The modern common-rail diesel injector system has been developed by the industry to fulfil these aspirations, designed with ever-higher tolerances pressures, which have led to concomitant increases in fuel temperatures after compression with reports of fuel temperatures of ~150°C at 1500-2500 bar. This engineering solution in combination with the introduction of Ultra Low Sulphur diesel fuel (ULSD) has been found to be highly sensitive to deposit formation both external injector deposits (EDID) and internal (IDID). The deposits have caused concerns for customers with poor spray patterns misfiring injector malfunction and failure producing increased fuel consumption and emissions. The importance to the industry of understanding the nature of diesel injector deposits has led to significant research in this area with a number of industry tests being developed. However, the introduction of new generation fuels e.g. hydrogenated vegetable Oil (HVO) and the reports of injector problems such as "abrasive particles" in Europe continue to stimulate investigation. The interest in characterizing diesel injector deposits has also seen a number of recent contributions being published. Many of these reports describe analyses that either consider only the surface of deposits or use methods which destroy any provenance. In this paper, we will describe the latest data from the deployment of modern analytical techniques to characterize these deposits. As a further contribution to the understanding of diesel injector deposits, this paper will describe the use of Principal Component Analysis (PCA) in conjunction with Time of Flight Secondary Ion Mass spectrometry (ToF-SIMS) to determine trends in IDID chemistries worldwide. The application of the ToF-SIMS technique to EIDS will be described. The latest industry standard engine tests will be discussed with regard to the chemistries involved and the latest advances in the application of a new generation of deposit control additives (DCA) will be described.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.