The identification results for the static performance characteristics of a large tilting-pad bearing in load between pad configuration are presented for specific bearing loads between 1.0 and 2.5 MPa and for circumferential speeds up to 79 m/s. The bearing is lubricated by spray-bars and can be described by the following specifications: Five pads, 0.23 nominal preload, 60% offset, 56° pad arc angle, 500 mm inner diameter, 350 mm pad length and 1.28 per mille relative bearing clearance. The axial oil flow is reduced by a fixed seal on both bearing edges which has a nominal radial clearance of 1 mm. The film pressure and the gap width are determined in the whole area of the sliding surface by an axial shift of the shaft. The bearing temperatures are measured by means of 100 thermocouples located 5 mm behind the sliding surface. The experimental results indicate that significant pad deformation occurs in circumferential and in axial direction. Also the effective supply temperatures are much higher than the nominal ones. According to the lubricant flow the sensor temperatures close to the spray-bars at the sliding surface rise about 20 K for 7 l/s and 40 K for 3.5 l/s at 3000 rpm. The temperatures are nearly constant between all pads and depend only on speed and not on load. The theoretical analyses of the bearing performance was accomplished with the bearing calculation software COMBROS. This code models the transition between laminar and turbulent flow and solves an extended Reynolds equation, the three dimensional energy equation of the film and the heat conduction equations of the shaft and the pads considering various boundary conditions due to the judgment of the user. Concerning the minimum film thickness, the maximum temperature on the sliding surface and the maximum film pressure only poor agreement was reached if the influence of the axial pad deformation was neglected. In advanced analyses a co-simulation between COMBROS and a structural mechanics software shows that an improvement of the prediction was achieved. The comparison of the measurement data and the advanced simulation shows very good agreement for the characteristic bearing parameters as well as for the local distributions of film pressure, temperature and film thickness in the whole operating range of the bearing. Further, the applied inlet mixing model for the lubricant supply process proves to be very suitable.

The identification results for the linear dynamic coefficients of a K-C model for a large tilting-pad bearing in load between pad configuration are presented for specific bearing loads between 1.0 and 2.0 MPa and circumferential speeds of 39 m/s and 78 m/s. The bearing with a double tilting support is lubricated by spray-bars and can be described by the following specifications: Five pads, 0.23 nominal preload, 60% offset, 56° pad arc angle, 500 mm inner diameter, 350 mm pad length and 1.28 per mill relative bearing clearance. The test rig and the test procedure are described in detail. For the determination of the dynamic coefficients, a harmonic force is induced by two unbalance-vibration generators being attached to the frame of the rig. The relative movement between bearing and shaft is detected by proximity probes between bearing housing and shaft. The bearing forces are identified by measurements of the entire film pressure distribution in both circumferential and axial direction. In the post processing of the data, the dynamic force components are determined by a Fourier-analysis. This procedure is well-established for fixed-pad bearings. However, the uncertainties of its capabilities for tilting-pad bearings are investigated and discussed in this study. The theoretical analyses with the code COMBROS are based on a calculation of linear perturbations for the predicted static properties. The measurement and the calculation procedures show very good agreement for fixed-pad bearings. For a tilting-pad bearing the results differ with increasing frequency ratio and rotational speed. The experimental results show very poor frequency dependence in load direction and a very high one in the orthogonal direction. Theoretically, the influence of the frequency ratio is comparable in both planes and pretty low due to the pivot offset and the high effective preload. While good agreement for the measured and predicted K-C model can be observed at the lower rotational and vibrational frequency the correspondence becomes worse with the increase of both. The identification procedure uses the fluid film force to determine the dynamic coefficients and assumes that this is equal to the load on the bearing in every time step. The results indicate that the experimental identification is uncertain due to the elasticity of the double tilting bearing support and the initiated dynamic effects of it. An improvement of the measurement that also identifies the limitation of the current procedures as well as simplifications in the theoretical analyses are discussed.

To improve operational safety and/or achieve a higher load capacity of turbine tilting-pad bearings, an axially concave pad profile is presented. The thermal and mechanical stress of the loaded pads of a test bearing in load between pivot configuration has been analysed. Both film thickness and pressure distribution have been measured at a very high resolution. A fluid film calculation program in combination with a finite-volume-based structural mechanics program is used to simulate the deformation of a single pad under high circumferential speeds. In this context, the axial and tangential heat transfer coefficients of the pad surface, which act as boundary conditions for the calculation of the 3D temperature distribution, are determined using an optimization process. Herein, the match of predicted and measured pad temperatures is the goal. It can be shown that there must be a huge difference in heat transfer in axial and tangential direction in order to match the large measured temperature gradient in circumferential direction. Based on the measured deformed profile the program code is used to derive a concave pad profile, which will result in an axially non-arched sliding surface under the expected thermal load. Therefore, an iterative simulation procedure is used. By decreasing the axial arching of the pad and thus the large film thickness at the axial ends using an improved profile designed for a specific operation point, the minimum film thickness and maximum pad temperature can be influenced beneficially. The comparison of measurement data and calculation results shows very good agreement regarding the pad deformations. The results indicate that by axially concave profiling of the loaded pads of a large tilting-pad bearing for a specific operation point, the static characteristics in the form of temperature, film thickness and load capacity can be improved.

Large turbine bearings are usually equipped with hydrostatic jacking mechanisms to separate bearing and shaft during transient start-stop procedures. They are turned off once hydrodynamic operation is reached. In some cases, under severe operating conditions, the hydrostatic oil supply is kept running although the rotor already runs in full speed. The supplied amount of jacking oil is very small compared to the regular oil supply. However, experimental data of a large tilting-pad bearing shows that this hybrid operation has a considerable impact on the load carrying capacity in terms of lower pad temperature and larger film thickness. In this paper, a theoretical investigation to analyse the effect of increased load carrying capacity of a large tilting-pad journal bearing in hybrid operation is presented. The increase is driven by three different aspects: 1) hydrostatic pressure component, 2) increase in lubricant viscosity due to the injection of cold oil, 3) decrease of temperature gradients and thus thermal pad deformation. Subject of the approach is a ø500 mm five-pad, rocker-pivot tilting-pad journal bearing in flooded lubrication mode. The experiments are carried out on the Bochum test rig for large turbine bearings. The theoretical analyses are performed with a simulation code solving the Reynolds and energy equations for the oil film and calculating the thermomechanical pad deformations simultaneously. By considering each of the three above aspects separately and in combination, their share of load increase can be assessed individually. Contrary to expectations, the results indicate that the increase is not mostly based on the hydrostatic pressure component. Instead, the advantageously decreased pad deformations make the largest contribution to the increased load carrying capacity while the alteration in viscosity shows the least impact.

In this paper a theoretical study with the aim to achieve higher load capacity of large tilting-pad turbine bearings is presented. The main focus is set on the reduction of thermal gradients inside the pad and thus, of adverse thermomechanical deformations. This allows for the increase of either the load carrying capacity, minimum film thickness hmin, and/or decrease maximum pad temperature Tmax. Subject of the investigation is a 5-pad tilting-pad bearing with rocker pivots. Each pad arc measures 56° and the pivot is positioned at 60 %. By having a 500mm inner diameter the 350mm long bearing features a relative clearance of 1.28% and nominal preload of 0.23. It is shown that the axial pad bending Δh (crowning) has a major impact on film thickness and pressure distributions and thus on the operational safety parameters. In order to reduce this effect, radial bores through the pad supplying pressurized cold oil (Tinj = 50 °C) are simulated. Despite the evident increase in oil film pressure, the primary purpose of the injection is to rinse away the layer of hot oil sticking to the pad surface. The maximum pad temperature and the overall pad temperature gradients are thereby decreased. The code used for simulation solves Reynolds and energy equations and computes thermomechanical deformations simultaneously. However, the simulations are carried out for one single pad only and are therefore supported by boundary conditions taken from experiments. In order to determine the impact of the approach on the static bearing characteristics, diameter and location of the bores are varied (0.3mm ≤ db ≤ 0.5mm). It is shown that pad crowing can be reduced significantly: The axial deviation of the film thickness Δh can be decreased from Δh = 47 μm to Δh = 31 μm, while the maximum temperature Tmax can be decreased by 20 K. Further, the minimum film thickness hmin can be increased by 16 μm. Subsequently, allowing the same limits for hmin and Tmax for the new design, the load capacity can be raised by up to 1.21MPa ≙ 44 %.