In this paper, CdTe quantum dots (QDs)doped single electrospun polymer nanofibers are partially coated with gold nanoparticles to form distinct hybrid photonic-plasmonic nanoresonators to investigate the critical role of the cavity-confined hybrid mode on the modification of the spontaneous emission dynamics of the fluorescent emitters in low-Q photonic cavities. A total enhancement factor of 11.2 is measured via a time-resolved experimental technique, which shows that there is an increase of about three times in the spontaneous emission rate for the QDsdoped gold nanoparticle-decorated nanofibers as they are compared with those uncoated ones. The physical mechanism affecting the spontaneous emission rate of the encapsulated QDs in such a hybrid photonic-plasmonic nanoresonator is explained to be due to regeneration of the mode field in the nanofiber cavity upon the interaction of the dipoles with the surface plasmons of distinctive gold nanoparticles that surround the outer surface of the nanofiber.

Green light-emitting CdSe@ZnS/ZnS (QD) nanoparticles were synthesized; the photophysical and morphological properties of their films, which were prepared by spin coating from six different concentrations, corresponding to absorbance values of 0.6, 1.1, 1.6, 2.1, 2.8, and 4.0, were determined. Increasing the absorbance value from 0.6 to 4.0 did not change the photophysical properties of QD films to a large extent, whereas it resulted in an increment in QD film thickness from 20 to 110 nm. The films were utilized as an emissive layer in QD light-emitting diodes with poly­(9-vinylcarbazole) (PVK), PVK:2-(4-biphenyllyl)-5-(4-tert-butylphenyl)-1,3,4-oxadiazole (PBD), and PVK:1,3-bis­[(4-tert-butylphenyl)-1,3,4-oxadiazolyl]-phenylene (OXD-7) hole-transport layers (HTLs). The presence of PBD or OXD-7 in PVK reduced the efficiency values but played a positive role in the color purity and efficiency roll off. The maximum color temperature and electroluminescence wavelength shifts obtained with applied potential were 109, 50, and 50 K and 11, 5, and 5 nm for pure-PVK, PVK:PBD, and PVK:OXD-7-based devices, respectively. Hole mobility, capacitance (at 103 Hz), and charge-transfer efficiency values were 9.0 × 10–7, 6.8 × 10–7, and 4.2 × 10–7 cm2 V s–1, 1.7, 1, and 1 nF, and 6.90%, 15.50%, and 16.10% for pure-PVK, PVK:PBD, and PVK:OXD-7-based devices, respectively. Enhanced color purity and lowered efficiency roll off obtained with PVK:PBD and PVK:OXD-7 HTLs were attributed to decreased capacitance, increased charge-transfer efficiency, and reduced Joule heating.

Impurities in trioctylphophine (TOP) strongly affect nanocrystal synthesis. 1-Octanol among other contaminants in TOP is identified for the first time as a functional impurity by 1 H NMR. The deliberate addition of 1-octanol into trioctylphosphine reduced particle size and modified photophysical properties of ZnCdSSe/ZnS colloidal nanocrystals. NMR analysis furthermore revealed that 1-octanol is bonded to the nanocrystal surfaces. The ratio of integrals for the O−CH 2 protons of 1-octanol, which is the lowest compared to the other ligands, suggests that 1-octanol plays a critical role to tune the particle size of nanocrystals. The increased amount of 1-octanol added into TOP reduces the particle size from 9.8 to 7.2 nm, causing a progressive blue shift in the UV−vis and PL spectra but leaving the alloy composition unaffected. The rate of nonradiative processes is enhanced with the amount of 1-octanol added into TOP, correlating with higher dislocation density observed in the nanocrystals. As a conclusion, 1-octanol is proposed as a functional impurity that varies particle size and nonradiative photophysical processes in the ZnCdSSe/ZnS colloidal nanocrystals.

Counterfeiting is a growing issue and causes economic losses. Fluorescent inks containing In(Zn)P/ZnS/DDT core/shell colloidal nanoparticles are formulated and combined with a convenient optical device for authentication. The particle size...

Counterfeiting is a growing economic and social problem. For anticounterfeiting, random and inimitable droplet/fiber patterns were created by the electrospinning method as security tags that are detectable under UV light but invisible in daylight. To check the authenticity of the original security patterns created; images were collected with a simple smartphone microscope and a database of the recorded original patterns was created. The originality of the random patterns was checked by comparing them with the patterns recorded in the database. In addition, the spectral signature of the patterns in the droplet/fiber network was obtained with a simple and hand-held spectrometer. Thus, by reading the spectral signature from the pattern, the spectral information of the photoluminescent nanoparticles was verified and thus a second-step verification was established. In this way, anticounterfeiting technology that combines ink formula, unclonable security pattern creation and two-level verification is developed.