A string of monocyanated quinoxaline (Qx)-based D–A-type polymers systematically decorated with electron-attracting chlorine (Cl) atoms was created for use in non-fullerene polymer solar cells (PSCs). First, coupling of the benzodithiophene (BDT) donor and Qx acceptor with the strong electron-attracting cyano (CN) unit at its 5-position yielded the monocyanated reference polymer PB-CNQ. Subsequently, the additional Cl atoms were separately or simultaneously incorporated into the thiophene side groups of the BDT donor and Qx acceptor to create other objective polymers, PBCl-CNQ, PB-CNQCl, and PBCl-CNQCl. The Cl substituents on the BDT donor and Qx acceptor are represented by the names of the polymers. Owing to the favorable contributions of Cl substituents, the inverted-type non-fullerene PSCs based on partially chlorinated PBCl-CNQ (12.80%) and PB-CNQCl (13.93%) exhibited better power conversion efficiencies (PCEs) than the device based on unchlorinated reference PB-CNQ (11.19%). However, a significantly reduced PCE of 9.84% was observed for the device based on PBCl-CNQCl, in which Cl atoms were loaded on both the BDT donor and Qx acceptor at the same time. Hence, these results reveal that optimization of the number and position of Cl substituents in monocyanated Qx-based polymers is essential for enhancing their photovoltaic nature through the synergistic effects between two strong electron-attracting CN and Cl substituents.

The choice of the chlorine (Cl) atom as an electron-withdrawing substituent in conjugated polymers leads to a higher potential in the commercialization of polymer solar cells than its fluorine counterpart because of the versatility and cost-effectiveness of the chlorination process. In addition, the population and location of Cl substituents can significantly influence the photovoltaic characteristics of polymers. In this study, three chlorinated quinoxaline-based polymers were invented to examine the numerical and positioning effects of the Cl atom on their photovoltaic characteristics. The number of Cl substituents in the reference polymer, PBCl-Qx, was adjusted to three: two Cl atoms in the benzodithiophene-type D unit and one Cl atom in the quinoxaline-type A unit. Subsequently, two more Cl atoms were selectively introduced at the 4- and 5-positions of the alkylated thiophene moieties at the 2,3-positions of the quinoxaline moiety in PBCl-Qx to obtain the additional polymers PBCl-Qx4Cl and PBCl-Qx5Cl, respectively. The conventional PBCl-Qx4Cl device exhibited a better power conversion efficiency (PCE) of 12.95% as compared to those of PBCl-Qx (12.44%) and PBCl-Qx5Cl (11.82%) devices. The highest PCE of the device with PBCl-Qx4Cl was ascribed to an enhancement in the open-circuit voltage and fill factor induced by the deeper energy level of the highest occupied molecular orbital and the favorable morphological features in its blended film with Y6.

To investigate the effect of miscibility between conjugated polymers (CPs) and Y6 on bulk-heterojunction (BHJ) type morphology, we propose three different CPs with similar chemical structures but different miscibility with Y6. After selectively removing Y6 from the CP/Y6 blend films, their interface morphology and interlocked dimensions are quantitatively compared using a square-wave model. As CP−Y6 miscibility increases, a higher intermixed interface is formed, providing an enlarged CP− Y6 interface area. Conversely, as the miscibility between CP and Y6 decreases, the height and width of the interlocked dimensions formed by phase separation gradually decrease and increase, respectively. Additionally, when the CP−Y6 interface morphology and electrical properties of the corresponding organic photovoltaic (OPV) device are correlated, as the highly intermixed CP−Y6 interface develops, the exciton dissociation efficiency increases owing to the reduced exciton diffusion length to be dissociated, but the bimolecular recombination tends to deteriorate simultaneously. Furthermore, if the miscibility between CP and Y6 is excessive, the formation of a charge transport pathway through phase separation is interrupted, deteriorating the charge transport capability in BHJ-type OPVs. However, it was confirmed that introducing F atoms into the conjugated backbone of CP can reduce the bimolecular recombination, providing ameliorated light-harvesting efficiency.

Herein, a string of quinoxaline-based D–A-type polymers possessing either electron-withdrawing or electron-donating groups were developed to explore their impact on the photovoltaic efficiency of the polymers. Once the reference polymer PBF-CF3Qx was prepared, extra fluorine atoms and methoxy units were selectively added on the 6,7-positions of the quinoxaline unit of the PBF-CF3Qx reference to provide two objective polymers, PBF-CF3QxF and PBF-CF3QxM, respectively. Owing to the significant influence of the existing electron-withdrawing or electron-donating substituents, each polymer displayed considerably discernible optical, electrochemical, and morphological features. Moreover, the conventional nonfullerene photovoltaic devices based on PBF-CF3QxF and PBF-CF3QxM exhibited superior power conversion efficiencies of 11.37 and 11.18%, respectively, compared to the device based on the PBF-CF3Qx reference 6.96%). These results emphasize the significance of electron-withdrawing and electron-donating substituents in quinoxaline-based polymers for controlling their intrinsic and photovoltaic attributes.