No abstract

A converter valve unit, which converts Alternating Current (AC) to Directing Current (DC) and DC to AC, is one of the key elements of high voltage direct current (HVDC) transmission. The insulation design of a converter valve unit should be considered for air clearance according to the DC superimposed overvoltage and the insulator that maintains the insulation performance and the corona shield to suppress DC corona discharge. There is no prescribed standard for the insulation design of a converter valve unit. Moreover, insulation performance under an applied DC voltage has not yet been thoroughly investigated. Therefore, it is necessary to study the insulation design method of the converter valve unit. In this paper, consideration of the insulation design method on a ± 200 kV converter valve unit in an HVDC converter hall is performed. The finite element method (FEM) is used to simulate the 3D model. Additionally, the safety factor () is applied in accordance with the dielectric test in IEC 62271-1. As a result, an insulation design process on the converter valve unit is proposed and the insulation design is carried through the design factors. It is confirmed that design factors on the air clearance, insulator and corona shield have a significant effect on a highly reliable insulation design.

The internal pressure of a vacuum interrupter (VI) is increased by arc heat, ceramic cracking, gas leakage, and manufacturing defects. Accordingly, the dielectric strength of VI rapidly decreases. To improve the reliability of power transmission, efficient maintenance through the real-time monitoring of the vacuum degree is essential. However, real-time monitoring of the vacuum degree is difficult, and related research is scarce. Additionally, due to the insulation problems of this technology, there are few commercially available products. Therefore, this paper proposes a method for real-time monitoring of the vacuum degree and an insulation supplement design for a distribution class VI. First, dielectric experiments were conducted to identify the section in which the dielectric strength of the VI rapidly decreased according to the vacuum degree. Second, for real-time monitoring of the VI, several factors were proposed through the partial discharge in the VI, while the capacitance characteristics of the VI were calculated to improve the signal of the internal partial discharge. Finally, to supplement the dielectric problems of the solid insulation high voltage apparatus that occur when real-time monitoring technology is applied, the insulation supplement design was performed through the finite element method (FEM).

A linear accelerator, called RAON, has been being developed as a part of Rare Isotope Science Project (RISP) by Institute for Basic Science (IBS) [1]. The linear accelerator utilizes an electron cyclotron resonance (ECR) ion source for providing intense highly charged ion beams to the linear accelerator. 28GHz ECR ion source can extract heavy ion beams from proton to uranium. A superconducting magnet system for 28GHz ECR ion source is composed of hexapole coils and four solenoid coils made with low Tc superconducting wires of NbTi [2].The electromagnetic force acts on the superconducting magnets due to the magnetic field and flowing current in case of not only normal state but also quench state [3]. In case of quench on hexapole coils, unbalanced flowing current among the hexapole coils is generated and it causes unbalanced electromagnetic force. Coil motions and coil strains in quench state are larger than those in normal state due to unbalanced electromagnetic force among hexapole coils. Therefore, analysis on electromagnetic characteristics of superconducting magnet for 28GHz ECR ion source according to the series resistance of protection circuit in case of quench should be conducted. In this paper, analysis on electromagnetic characteristics of superconducting hexapole coils for 28GHz ECR ion source according to the series resistance of protection circuit in case of quench is performed by using finite elements method (FEM) simulation. PACS number: 29.17, 29.17+W, 29.25.Ni

The vacuum degree of Vacuum Interrupter (VI) will deteriorate because of gases emitted by arc heat, and leakage through the joints. It is important to select an appropriate maintenance criteria for a VI by monitoring the vacuum degree. However, monitoring of a VI installed inside a solid insulation apparatus in a transmission system is impossible. Only studies on the insulation deterioration because of the decrease of the vacuum degree have been conducted, and important factors such as the maintenance criteria have not been investigated. Moreover, most studies have only been performed using AC voltage, not DC voltage. Therefore, in this paper, AC and DC partial discharge were compared by monitoring of the vacuum degree in a distribution class VI to propose maintenance criteria according to voltage type. Through this, for efficient maintenance, maintenance criteria of VI for each voltage type are presented. The vacuum degree at which the dielectric strength rapidly decreases was confirmed according to voltage type. The coupling capacitor was installed directly on the floating shield of VI. Moreover, to measure the pattern and apparent charge of partial discharge according to the vacuum degree, phase resolved partial discharge (PRPD) for AC partial discharge and pulse sequence analysis (PSA) for DC partial discharge were adopted. It is found that maintenance should be performed when the vacuum degree is in the range of 10 −3 ∼ 10 −2 torr regardless of the voltage type. Moreover, the usefulness of the technology is higher at AC voltage than at DC voltage.