Vacuum-Assisted Resin Infusion (VARI) and Resin Transfer Molding (RTM) techniques are the most common techniques for the manufacturing of polymeric composite laminates. The VARI technique has a lot of advantages such as low cost, free voids laminates and the ability to produce complex shapes. However, it has some drawbacks such as poor surface finish and temperature instabilities. On the contrary, the RTM technique can withstand high temperature, producing a good surface finish and complex shape laminates. However, it has a high tooling cost and poor quality laminates due to void contents. In this study, a new technique integrated both VARI and RTM techniques is developed to minimize their drawbacks. This technique involves using a semitransparent composite plate instead of a vacuum bag in the VARI technique. This semitransparent plate takes the inverse shape of the composite laminate similar to the RTM tooling. However, this plate has a low cost compared with RTM tooling and allows monitoring of the resin flow during the infusion process. To validate the integrated technique, the mechanical properties of composite laminates are compared with that produced by hand layup technique (HLT). Moreover, the influence of incorporation of 0.25 wt. % and 0.5 wt. % of titanium dioxide (TiO2) nanoparticle into woven and chopped fiber/epoxy composite laminates was demonstrated. The results indicated that the laminates fabricated by the integrated VARI method showed higher mechanical properties than those produced by the hand-layup technique. Moreover, glass fiber/epoxy filled with 0.25 wt. % of TiO2 nanoparticles gives high mechanical properties.
The manufacturing of nanocomposites using the Vacuum Resin Infusion (VRI) technique can be considered a challenging task. The reason for this challenge is the high viscosity of the nanofilled resin. For large composite laminates, the nanofilled resin may be cured before complete mold filling, and thus can be considered as a waste of money. In this study, different weight fractions of TiO2 nanoparticles (0.25 wt. % and 0.5 wt. %) were added to epoxy resin. Also, different weight fractions of ethanol (0.5 wt. % and 1 wt. %) were added to both unfilled and nanofilled epoxy. The processing time, hardness, and wear behavior of the composite laminates were investigated. It was found that the addition of TiO2 nanoparticles improved the hardness and wear behavior of composite laminates but the processing time was high. Also, results showed that adding a small amount of ethanol (0.5 wt. %) and 0.25 wt. % of TiO2 nanoparticles to epoxy reinforced with chopped/woven glass fiber not only reduced the processing time but also improved the hardness and wear resistance as compared to neat composite laminates. Moreover, adding 0.5 wt. % of ethanol and 0.25 wt. % of TiO2 nanoparticles to woven E-glass/epoxy (WN0.25E0.5) gives hardness and wear resistance close to that obtained with woven E-glass/epoxy filled with 0.5 wt. % of TiO2 nanoparticles (WN0.5). It is economical to manufacture WN0.25E0.5 rather than WN0.5 as the cost and processing time of WN0.25E0.5 is lower than WN0.5.
Vacuum resin infusion (VRI) is a promising technique for manufacturing complicated structural laminates. This high viscosity of nanofilled resin increases the filling time and leads to an incomplete mold filling. The mold filling time can be reduced either by making the fiber dimensions smaller than the mold (gaps around the fibers) or by adding ethanol to nanofilled epoxy. However, ethanol addition influences the mechanical properties of composite laminates. In this study, different amounts of ethanol (0.5 wt. % and 1 wt. %) were used as a diluent to both neat epoxy and epoxy filled with (0.25 wt. %) of titanium dioxide (TiO2) nanoparticles. From results, it was found that ethanol addition saves the time for neat and nanofilled epoxy by 47.1% and 24.1%, respectively. It was found that adding 0.5 wt. % of ethanol to 0.25wt. % of TiO2 nanoparticles (GT0.25E0.5) enhances the tensile and flexural strength by 30.8% and 55.9%, respectively compared with neat specimens. Furthermore, the tensile and flexural moduli increased by 62% and 72.3%, respectively. Furthermore, the mold filling time was investigated experimentally and validated numerically using ANSYS FLUENT software. The mold filling time prediction using ANSYS FLUENT can be used to avoid resin gelation before the incomplete mold filling and thus can be considered a cost-effective methodology. The results showed that the gaps around the fibers reduce the time by 178% without affecting the mechanical properties.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.