Liquid silicone rubber (LSR) techniques are experiencing exponential growth, particularly in the field of high technology due to the low-temperature flexibility, superior heat stability, chemical resistance, and aging resistance of LSR components. Enhancing the curing rate of LSR parts in liquid silicone rubber injection molding is an important research topic. In this study, an injection mold with high energy efficiency of vulcanization for the liquid silicone rubber injection molding of a fisheye lens was developed and implemented. The LSR injection mold has a conformal heating channel (CHC) and conformal cooling channel (CCC) simultaneously. The function of CHC is to enhance the curing rate of a fisheye lens in the LSR injection molding to meet the requirements of sustainable manufacturing. The curing rates of a fisheye lens were numerically examined using the Moldex3D molding simulation software. It was found that the curing rate of the fisheye optical lens cured by injection mold with CHC was better than that of the injection mold with a conventional heating channel. The curing efficiency could be increased by about 19.12% when the heating oil temperature of 180 °C was used to cure the fisheye optical lens. The simulation results showed that the equation y = −0.0026x3 + 1.3483x2 − 232.11x + 13,770 was the most suitable equation for predicting the curing time (y) through the heating oil temperature (x). It was found that the trend of the experimental results was consistent with the simulation results. In addition, the equation y = −0.0656x2 + 1.5827x − 0.894 with the correlation coefficient of 0.9974 was the most suitable equation for predicting the volumetric shrinkage of the fisheye optical lens (y) through the heating oil temperature (x). The volume shrinkage of the fisheye optical lens cured by injection mold with CHC was very similar to that of the injection mold with a conventional heating channel. The maximum volume shrinkage of the fisheye optical lens cured at 180 °C was about 8.5%.

Liquid silicone rubber (LSR) parts have some distinct characteristics such as superior heat stability, low-temperature flexibility, aging resistance, and chemical resistance. From an industrial standpoint, the uniform vulcanization temperature of LSR is an important research point. However, the uniformity of the vulcanization temperature of LSR has been limited since the layout of the cartridge heater incorporated in the conventional steel mold does not follow the profile of the mold cavity. Metal additive manufacturing can be used to make LSR injection molds with conformal heating channels and conformal cooling channels simultaneously. However, this method is not suitable for a mold required to develop a new LSR product. In this study, a cost-effective approach was proposed to manufacture an LSR injection mold for the pilot run of a new optical lens. A rapid tool with low vulcanization energy consumption channels was proposed, which was incorporated with both a conformal heating channel (CHC) and conformal cooling channel (CCC) simultaneously. The function of the CHC was to vulcanize the LSR in the cavity uniformly, resulting in a shorter cycle time. The function of the CCC was to keep the LSR in a liquid state for reducing runner waste. It was found that the equation of y = −0.006x3 + 1.2114x2 − 83.221x + 1998.2 with the correlation coefficient of 0.9883 seemed to be an optimum trend equation for predicting the solidification time of a convex lens (y) using the vulcanizing hot water temperature (x). Additionally, the equation of y = −0.002x3 + 0.1329x2 − 1.0857x + 25.4 with the correlation coefficient of 0.9997 seemed to be an optimum prediction equation for the solidification time of a convex lens (y) using the LSR weight (x) since it had the highest correlation coefficient. The solidification time of a convex lens could be reduced by about 28% when a vulcanizing hot water temperature of 70 °C was used in the LSR injection mold with CHC.

Rotary friction welding (RFW) is a green manufacturing technology with environmental pollution in the field of joining methods. In practice, the welding quality of the friction-welded parts was affected by the peak temperature in the weld joint during the RFW of dissimilar plastic rods. In industry, polycarbonate (PC) and acrylonitrile butadiene styrene (ABS) are two commonly used plastics in consumer products. In this study, the COMSOL multiphysics software was employed to estimate the peak temperature in the weld joint during the RFW of PC and ABS rods. After RFW, the mechanical performance and microstructural evolution of friction-welded parts were investigated experimentally. The average Shore A surface hardness, flexural strength, and impact energy are directly proportional to the rotation speed of the RFW. The quality of RFW is excellent, since the welding strength in the weld joint is better than that of the ABS base materials. The fracture occurs in the ABS rods since their brittleness is higher than that of the PC rods. The average percentage error of predicting the peak temperature using COMSOL software using a mesh element count of 875,688 for five different rotation speeds is about 16.6%. The differential scanning calorimetry curve for the friction-welded parts welded at a rotation speed of 1350 rpm shows an endothermic peak between 400 to 440 °C and an exothermic peak between 600 to 700 °C, showing that the friction-welded parts have better mechanical properties.

Rotary friction welding (RFW) could result in lower welding temperature, energy consumption, or environmental effects as compared with fusion welding processes. RFW is a green manufacturing technology with little environmental pollution in the field of joining methods. Thus, RFW is widely employed to manufacture green products. In general, the welding quality of welded parts, such as tensile strength, bending strength, and surface hardness is affected by the peak temperature in the weld joint during the RFW of dissimilar plastic rods. However, hitherto little is known about the domain knowledge of RFW of acrylonitrile butadiene styrene (ABS) and polycarbonate (PC) polymer rods. To prevent random efforts and energy consumption, a green method to predict the peak temperature in the weld joint of dissimilar RFW of ABS and PC rods was proposed. The main objective of this work is to investigate the peak temperature in the weld joint during the RFW using COMSOL multiphysics software for establishing an empirical technical database of RFW of dissimilar polymer rods under different rotational speeds. The main findings include that the peak temperature affecting the mechanical properties of RFW of PC and ABS can be determined by the simulation model proposed in this work. The average error of predicting the peak temperature using COMSOL software for five different rotational speeds is about 15 °C. The mesh element count of 875,688 is the optimal number of meshes for predicting peak temperature in the weld joint. The bending strength of the welded part (y) using peak welding temperature (x) can be predicted by the equation of y = −0.019 x2 + 5.081x − 200.75 with a correlation coefficient of 0.8857. The average shore A surface hardness, impact energy, and bending strength of the welded parts were found to be increased with increasing the rotational speed of RFW.

Friction welding (FW) FW of dissimilar polymer rods is capable of manufacturing green products swiftly and economically. In this study, a green manufacturing technique of joining dissimilar polymer rods was proposed, and the effects of rotational speed on the joint characteristics of friction-welded dissimilar polymer rods fabricated by the fused deposition modeling process were investigated experimentally. The shore surface hardness test, impact test, three-point bending test, and differential scanning calorimetry analysis were carried out on the weld joints. The impact energy for FW of polylactic acid (PLA) and PLA, PLA and acrylonitrile butadiene styrene (ABS), PLA and PLA filled with glass fiber (GF), PLA and PLA filled with carbon fiber (CF), PLA and polycarbonate (PC), and PLA and polyamide (PA) rods can be increased by approximately 1.5, 1.5, 1.3, 1.3, 2.1, and 1.5 times by increasing the rotational speed from 330 rpm to 1350 rpm. The bending strength for FW of PLA and PLA, PLA and ABS, PLA and PLA filled with GF, PLA and PLA filled with CF, PLA and PC, and PLA and PA rods can be increased by approximately 1.3, 1.7, 1.3, 1.2, 1.2, and 1.2 times by increasing the rotational speed from 330 rpm to 1350 rpm. However, the surface hardness of the weld bead is not proportional to the rotational speed. The average surface hardness of the weld bead was increased by approximately 5% compared to the surface hardness of the welding base materials.