The fractured carbonate rock reservoir is widespread in Sichuan Basin, and the characteristics of different areas are different. The development of natural fractures is varying degrees, lost circulations occur frequently, and the formation heterogeneity is strong, which causes the formation not sufficiently stimulated by acidizing. It may affect the effectiveness of reservoir stimulation. To advance the whole stimulation effect of the heterogeneous fractured carbonate reservoir, a new solution for determining the invasion radius during drilling in a fracture network reservoir is presented, which is based on solute transport and convection-diffusion equations. It can predict the invasion radius caused by mud loss and determines the range of mud loss invasion, which clarify the scope and degree of reservoir damage. The formation of skin factors polluted by mud loss was calculated. The experiments verified that the acidizing technology can remove reservoir damage and reduce the polluted formation of skin factors. The opening pressure of the nature fracture closed is calculated which can control the acidizing area. It is confirmed how many fractures in the carbonate reservoir can be opened under the wellhead pressure limit, which meets the construction conditions of acidizing fractured reservoirs. The framework of network-fracture deep acidizing technology was established, which can efficiently break through the detrimental zone caused by lost circulation, break down the natural fracture network, and decrease the formation of the skin. The restart pressure of natural fractures was calculated, and the design parameters such as pump pressure and displacement were optimized to quantify the scope of reservoir stimulation and the scale of acid fluid. The technique of network-fracture deep acidizing was applied for well A, the formation of skin after acidizing can be reduced to -4, and the testing production of well A was 58.87×104 m3/d. The technique of network-fracture deep acidizing can quantify the acid scale and sweep area in acid fracturing design, which develops the fracturing efficiency and improves the fracturing engineering.

During drilling in deep shale gas reservoirs, drilling fluid losses, hole wall collapses, and additional problems occur frequently due to the development of natural fractures in the shale formation, resulting in a high number of engineering accidents such as drilling fluid leaks, sticking, mud packings, and buried drilling tools. Moreover, the horizontal section of horizontal well is long (about 1500 m), and the problems of friction, rock carrying, and reservoir pollution are extremely prominent. The performance of drilling fluids directly affects drilling efficiency, the rate of engineering accidents, and the reservoir protection effect. In order to overcome the problems of high filtration in deep shale formations, collapse of borehole walls, sticking of pipes, mud inclusions, etc., optimization studies of water-based drilling fluid systems have been conducted with the primary purpose of controlling the rheology and water loss of drilling fluid. The experimental evaluation of the adsorption characteristics of “KCl + polyamine” anti-collapse inhibitor on the surface of clay particles and its influence on the morphology of bentonite was carried out, and the mechanism of inhibiting clay mineral hydration expansion was discussed. The idea of controlling the rheology and water loss of drilling fluid with high temperature resistant modified starch and strengthening the inhibition performance of drilling fluid with “KCl + polyamine” was put forward, and a high temperature-resistant modified starch polyamine anti-sloughing drilling fluid system with stable performance and strong plugging and strong inhibition was optimized. The temperature resistance of the optimized water-based drilling fluid system can reach 180 °C. Applied to on-site drilling of deep shale gas horizontal wells, it effectively reduces the rate of complex accidents such as sticking, mud bagging, and reaming that occur when resistance is encountered during shale formation drilling. The time for a single well to trip when encountering resistance decreases from 2–3 d in the early stages to 3–10 h. The re-use rate of the second spudded slurry is 100 percent, significantly reducing the rate of complex drilling accidents and saving drilling costs. It firmly supports the optimal and rapid construction of deep shale gas horizontal wells.

No abstract

Foam gel fracturing fluid has the characteristics of low formation damage, strong flowback ability, low fluid loss, high fluid efficiency, proper viscosity, and strong sand-carrying capacity, and it occupies a very important position in fracturing fluid systems. The rheological properties of gel fracturing fluid with different foam qualities of CO2, under different experimental temperatures and pressures, have not been thoroughly investigated, and their influence on it was studied. To simulate the performance of CO2 foam gel fracturing fluid under field operation conditions, the formula of the gel fracturing fluid was obtained through experimental optimization in this paper, and the experimental results show that the viscosity of gel fracturing fluid is 2.5 mPa·s (after gel breaking at a shear rate of 500 s−1), the residue content is 1.3 mg/L, the surface tension is 25.1 mN/m, and the interfacial tension is 1.6 mN/m. The sand-carrying fluid has no settlement in 3 h with a 40% sand ratio of 40–70-mesh quartz sand. The core damage rate of foam gel fracturing fluid is less than 19%, the shear time is 90 min at 170 s−1 and 90 °C, the viscosity of fracturing fluid is >50 mPa·s, and the temperature resistance and shear resistance are excellent. The gel fracturing fluid that was optimized was selected as the base fluid, which was mixed with liquid CO2 to form the CO2 foam fracturing fluid. This paper studied the rheological properties of CO2 foam gel fracturing fluid with different CO2 foam qualities under high temperature (65 °C) and high pressure (30 MPa) and two states of supercooled liquid (unfoamed) and supercritical state (foamed) through indoor pipe flow experiments. The effects of temperature, pressure, shear rate, foam quality, and other factors on the rheological properties of CO2 foam gel fracturing fluid were considered, and it was confirmed that among all the factors, foam quality and temperature are the main influencing factors, which is of great significance for us to better understand and evaluate the flow characteristics of CO2 foam gel fracturing fluid and the design of shale gas reservoir fracturing operations.

Major shale gas exploration and development fields are located in the Sichuan basin. It requires huge water sources for shale gas fracking, but the well sites are mostly in the hills, which limits the industrialization of shale gas development. CO2 foam fluids can meet the requirements of fracking fluids and relieve water stress. It analyzed the feasibility of CO2 foaming fracturing for shale gas formation fracturing, proposed a design philosophy for CO2 foaming fracturing, and optimized fracturing parameters such as foam mass, proppant concentration, friction, and discharge rate. The flowchart of CO2 foam fracturing was established in, where the fracture morphology and propagation behavior of CO2 foam fracturing were obtained from numerical simulations comparable to the hydraulic fracture generated by conventional hydraulic fracturing. The CO2 foaming fracturing technique can provide a discharge rate of 6.0 m3/min and fluid volume and captures the volume effect of the current stimulated reservoir, which needs to be improved. It can be considered an initial survey of CO2 foam fracturing available in the Sichuan Basin shale formation, which may provide new methods and clues for stimulation.