This research studied how to develop tight upper sportswear from 3D scan data considering fabric stretch property. Subjects were five Korean men of average figure in their 20's. Scanning was done for ten postures via vitus smart/pro(Techmath LTD). Analyzing from 3D scan data, more than 70% of the upper body surface showed surface change rate under 20%. It was shoulder and under arm side part that showed most noticeable body surface change when moving. A parametric model with convex surface was generated and flattened onto the plane, resulting 2D pattern. The error rate occurring in the process of 3D to 2D conversion was 0.2% for outline and 0.13% for area, respectively. Thirteen kinds of stretchable fabrics in the market were collected for this study. Stretch property was in the range of 16.0~58.2% for wale direction; 23.1~78.4% for course. Based on wear trial test, four fabrics were chosen for making the 1st experimental garment and finally one fabric was chosen for the 2nd one, which was developed applying 4 kinds of crosswise reduction rate on 2D pattern: 0, 5, 10, and 15%. Through wear trial test and garment pressure measurement, experimental garment applied with 10% pattern reduction rate was evaluated as most comfortable and considerable.

This study was undertaken to develop protective gloves for rose farmers who work on thorny plant in Korea. Prototype of protective gloves was designed and evaluated in terms of thermal comfort and mobility. Gloves were made with arm protectors attached to them, so that they could protect the lower part of arms, and rubber bands were inserted into the arm protectors for them not to slip down. The bending part of each finger was punched in order to give ventilation. Also, the bending parts of the fingers in the upper and lower part of gloves were inserted with sponges and were stitched together in order to enhance gripping movement. According to compared evaluation of the developed gloves and the existing gloves, temperature inside the gloves didn't show any significant differences, but humidity inside the gloves showed significant differences. There were significant differences in terms of comparison of objective mobility, that is, pegboard run-time and grip power, from statistical aspects. In addition, a comparison of subjective discomfort showed significant differences and so the suitability of developed gloves was proved.

: The purpose of this study was to develop a plausible methodology based on experimental data how to set up darts and split lines on 3D parametric body dressed with tight-fit garment. The results were as following: Through the process of making convex hull, the concave parts were straightened to make a convex hull, especially in the center part of bust, under breast part and scapular part. To figure out the optimum positions of darts and split lines, the inflection points of curve ratio were searched along the horizontal polylines of waist and bust. This procedures produced reliable results with low deviation. Using Rapidform, CATIA and Unigraphics, six patches of bodice patterns were drawn and aligned. Paired t-test results showed the outline and area between 3D surface and 2D were not significantly different, meaning this method could be adaptable when flattening 3D surfaces. The amount of waist dart measured on the pattern showed that the highest portion was allocated on 2nd dart(back), followed by 1st dart(back), 1st dart(front), 2nd dart(front)/side dart, and center back dart. A series of findings suggested that curve ration inflection point could be used as a guide to set up darts and split line on 3D parametric model with low deviation.

: This study was designed to generate briefs pattern for women in their twenties using 3D parametric body model. 151 women in their 20's were random sampled and measured using Martine's anthropometry. And one subject was chosen as the representative subject for 3D scanning. Parametric model was generated of using CATIA P3, Unigraphics NX4.0, Rapidform 2006. And the 3D surface of parametric body model was flattened onto the 2D plane. 3 downscale ratios(0%, 10%, 15%) were applied to generated pattern to figure out what downscale ratio was suitable to make briefs with stretch fabric. 4 kinds of experimental briefs were made with stretch fabrics(0%, 10%, 15% downscale) and worn on the dressform. Subjective evaluation on the appearance was done and the data was analyzed by ANOVA with post-hoc test. Briefs pattern was generated through the process of flattening the parametric surface and arranging the patches to make briefs pattern by dart manipulation. The different ration of outline and area between 3D surface and 2D pattern were 0.22% and 0.09% respectively. It showed that a parametric model could provide a desirable pattern with minute size error. The results of subjective evaluation on the appearance of 4 experimental briefs showed that stretch briefs with 15% downscale ratio was evaluated most highly in most items. Findings imply that it is feasible to apply 3D parametric model to generate patterns for various items considering various fabric properties.