The aim of this work was to investigate the microstructure and the mechanical properties of laser-welded joints combined of Dual Phase DP800 and DP1000 high strength thin steel sheets. Microstructural and hardness measurements as well as tensile and fatigue tests have been carried out. The welded joints (WJ) comprised of similar/dissimilar steels with similar/dissimilar thickness were consisted of different zones and exhibited similar microstructural characteristics. The trend of microhardness for all WJs was consistent, characterized by the highest value at hardening zone (HZ) and lowest at softening zone (SZ). The degree of softening was 20 and 8% for the DP1000 and DP800 WJ, respectively, and the size of SZ was wider in the WJ combinations of DP1000 than DP800. The tensile test fractures were located at the base material (BM) for all DP800 weldments, while the fractures occurred at the fusion zone (FZ) for the weldments with DP1000 and those with dissimilar sheet thicknesses. The DP800-DP1000 weldment presented similar yield strength (YS, 747 MPa) and ultimate tensile strength (UTS, 858 MPa) values but lower elongation (EI, 5.1%) in comparison with the DP800-DP800 weldment (YS 701 MPa, UTS 868 MPa, EI 7.9%), which showed similar strength properties as the BM of DP800. However, the EI of DP1000-DP1000 weldment was 1.9%, much lower in comparison with the BM of DP1000. The DP800-DP1000 weldment with dissimilar thicknesses showed the highest YS (955 MPa) and UTS (1075 MPa) values compared with the other weldments, but with the lowest EI (1.2%). The fatigue fractures occurred at the WJ for all types of weldments. The DP800-DP800 weldment had the highest fatigue limit (348 MPa) and DP800-DP1000 with dissimilar thicknesses had the lowest fatigue limit (<200 MPa). The fatigue crack initiated from the weld surface.

No abstract

Filler wire metallurgy was modified through temporally shaped laser pulses, controlling cooling cycles in a recently developed method. Trends were identified through efficient mapping while maintaining representative thermal cycles of welding processes. A primary pulse melted preplaced filler wires while a secondary, linearly ramped-down pulse elevated the nugget to re-austenization temperatures. Ramped-down pulses resulted in linear cooling rates comparable with and exceeding furnace-based methods, between 50 and 300 • C/s. The linear decay of laser output power guided the temperature through a regime to obtain desired microstructures. For three very high-strength steel filler wire chemistries, quenching resulted in smaller plates with cross-hatched microstructures, accompanied by grain boundary ferrite. Finer bainite microstructures started forming for fast linear temperature decay, about 250 • C/s. Slower decay or a weaker third cycle formed coarser microstructures with coalescent sheaves and less cross-hatching.

A robust method is introduced to simulate and study the filler wire metallurgy for controlled cooling conditions after melting, enabling efficient mapping with prompt analysis of trends. Proposed is a reduced, though representative, process with more controllable conditions. Short lengths of filler wires are preplaced in a cavity, drilled into a base metal sheet. Irradiation by a pulsed laser beam melts the wire to generate a sample nugget. Pulse shaping influences the cooling rate, granting the ability to tailor weldament microstructures. The method is demonstrated for S1100QL steel and undermatched filler wire, to obtain high toughness for processes like laser-arc hybrid welding, where a representative thermal cycle is needed. For high toughness, a controlled amount of acicular ferrite and, in turn, nonmetallic inclusions is desirable. This "snapshot" method has revealed a characteristic histogram of inclusion sizes, for different pulse shapes. Additional information on the thermal cycle can be acquired by employing thermocouples, a pyrometer, or advanced methods like high speed imaging or modeling. The method offers a wide spectrum of variants and applications.

No abstract