Transformerless grid-connected inverters have attained a lot of research interest in renewable energy interface applications, due to certain promising properties like greater efficiency, light weight, affordable price, and tolerable power density. Among various types of transformerless grid-tied photovoltaic (PV) inverters, multilevel inverters (MLIs) are mostly popular due to their ability to transmit reactive power, small filter size for reducing total harmonic distortion (THD) and their common-ground (CG) configuration to mitigate the detrimental leakage current due to the parasitic capacitances of the PV array. Again, among different types of MLIs for PV systems, switched-capacitor (SC) based multilevel inverter topologies are the burning topic in current decades due to their single source requirements for producing multilevel output voltage. However, for mostly used single-phase five-level inverters, most of the existing SC based topology requires at least two SCs for power conversion. In this paper, a five-level transformerless inverter based on a single SC is proposed, requiring only seven switches, no diode, a single capacitor, and one dc voltage source. The proposed transformerless MLI also has auto-boosting capability. Notably, the number of power switches operating at high frequency is limited to three, which lowers down the switching losses of the inverter. Rather than a new single SC based five-level transformerless inverter topology, a control scheme is also presented to inject a precisely regulated current into the grid that can govern both the active and reactive power support modes. In-depth comparisons between the proposed and cutting-edge MLIs are also provided. All these claims are validated through MATLAB/Simulink and PLECS computer simulation environments. A laboratory-scaled prototype is also built and tested to support the simulated claims further and validate the effectiveness and feasibility of the proposed five-level transformerless inverter topology.

The traditional DC-link indirect AC/AC power converters (AC/DC/AC converters) employ two-stage power conversion, which increases the circuit complexity gate driving challenges, placing an excessive burden on the processor while implementing complex switching modulation techniques and leads to power conversion losses due to the use of a large amount of controlled power semiconductor switches. On the contrary, the traditional direct AC/AC voltage controllers, as well as frequency changers, suffer from high total harmonic distortion (THD) problems. In this paper, a new single-phase to three-phase AC/AC step-down power converter is proposed, which utilizes a multi-linking transformer and bilateral triode thyristors (TRIACs) as power semiconductor switches. The proposed direct AC/AC power converter employs single-stage power conversion, which mitigates the complexity of two-stage DC-link indirect AC/AC converters and traditional single-stage AC/AC frequency changers. Instead of using high-frequency pulse width modulated gate driving signals, line frequency gate pulses are used to trigger the TRIACs of the proposed AC/AC converter, which not only aids in reducing the power loss of the converter but also mitigates the cost and complexity of gate driver circuits. The proposed AC/AC converter reduces the THD of the output voltage significantly as compared to traditional direct AC/AC frequency changers. The performance of the proposed AC/AC converter is validated against RL and induction motor load in terms of overall THD and individual harmonic components through MATLAB/Simulink environment. A reduced-scale laboratory prototype is built and tested to evaluate the performance of the proposed AC/AC power converter. The experimental and simulation outcomes reveal the feasibility and excellent features of the proposed single-phase to three-phase AC/AC converter topology.

Due to the rapid advancement of power semiconductor devices, the use of voltage source inverters (VSIs) has gained widespread acceptance. As a consequence, the performance of the voltage source inverter has emerged as a critical aspect that is highly reliant on the modulation strategy. The pulse width modulation (PWM) technique is the most widely utilized method of controlling power semiconductor switches of VSI. Power quality is always considered as an industrial concern for VSI-based power system such as grid-connected renewable energy systems and industrial motor drives which largely depends on the PWM technique used for switching. However, the existing PWM schemes for VSIs suffer from high total harmonic distortion (THD) and power loss problems. To mitigate the THD and power loss of VSI, a hybrid PWM technique has been proposed in this paper. The proposed hybrid PWM technique introduces a modified modulating signal along with newly shaped carrier signal. A two-level VSI is used to evaluate the performance of the proposed hybrid PWM technique both for with and without filter conditions against RL load. The proposed hybrid PWM technique offers 0.89% filtered voltage THD and 0.69% filtered current THD which are lower than that of existing PWM techniques. On the contrary, at without filter condition, the proposed hybrid PWM technique shows THDs of 45.77% and 12.50% for inverter output voltage and current, respectively which are also lower than those of existing PWM techniques. Apart from these, the proposed hybrid PWM technique reduces the switching and conduction power losses of the VSI as compared to existing PWM techniques. The simulation works are carried out in MATLAB/Simulink environment and a reduced scale experiment is conducted in laboratory to evaluate the performance of the proposed hybrid PWM technique.

No abstract

No abstract