Recently, a constricted attachment of an atmospheric pressure low-current argon arc in the centre of the flat end face of a thoriated tungsten cathode was observed and spectroscopically analysed. Its diameter of 0.6 mm and its length of the free standing part of 10 mm are the typical dimensions of electrodes for high-intensity discharge lamps. This paper gives a physical interpretation of the axially symmetric arc spot by a simulation of its properties with a cathodic sheath model which takes into account a reduction in the work function above a critical temperature of the cathode surface by a thorium ion current. At first the optical observation and spectroscopic investigations are recapitulated. Then, an overview is given on the essential elements which are needed to simulate the cathodic arc attachment on a hot electrode. A simulation of a central cathode spot with these elements gives results which are far away from the experimental findings if a constant work function φ is used. Therefore, a temperature-dependent work function φ(T) is introduced. This φ(T) transitions from 4.55 to 3 eV above temperatures of the order of 3000 K. With this emitter spot model a constricted arc attachment is obtained by simulation in the centre of the flat end face of the cathode in accordance with experiment. For currents below i arc,max ≈ 15.5 A, two spot solutions with different cathode falls are found. They form a current-voltage-characteristic consisting of two branches which extend from a turning point at i arc,max to lower currents. For i arc > i arc,max , only a diffuse mode of cathodic arc attachment is obtained. It is shown by a comparison with measured data for i arc = 7.5, 10, 12.5 and 15 A that the solution with the lower cathode fall is observed experimentally.

Short-arc lamps are equipped with tungsten electrodes due to their ability to withstand a high thermal load during operation. Nominal currents of more than one hundred amperes lead to a cathode tip temperature near the melting point of tungsten. To reduce the electrode temperature and, thereby, to increase the maintenance of such lamps, ThO2 or tentatively La2O3 are added to the electrode material. They generate a reduced work function by establishing a monolayer of emitter atoms on the tungsten surface. Emitter enrichments on the lateral surface of doped cathodes are formed. They are traced back to transport mechanisms of emitter oxides in the interior of the electrode and on the electrode surface in dependence of the electrode temperature and to the redeposition of vaporized and ionized emitter atoms onto the cathode tip by the electric field in front. The investigation is undertaken by means of glow discharge mass spectrometry, scanning electron microscope images, energy dispersive x-ray spectroscopy, and through measurements of the optical surface emissivity. The effect of emitter enrichments on the stability of the arc attachment is presented by means of temporally resolved electrode temperature measurements and by measurements of the luminous flux from the cathode-near plasma. They show that the emitter enrichments on the lateral surface of the cathode are attractive for the arc attachment if the emitter at the cathode tip is depleted. In this case, it moves along the lateral surface from the cathode tip to sections of the cathode with a reduced work function. It induces a temporary variation of the cathode tip temperature and of the light intensity from the cathode-near plasma, a so-called flickering. In particular, in case of lanthanated cathodes, strong flickering is observed.

No abstract

The gas phase emitter effect increases the lamp lifetime by lowering the work function and, with it, the temperature of the tungsten electrodes of metal halide lamps especially for lamps in ceramic vessels due to their high rare earth pressures. It is generated by a monolayer on the electrode surface of electropositive atoms of certain emitter elements, which are inserted into the lamp bulb by metal iodide salts. They are vaporized, dissociated, ionized, and deposited by an emitter ion current onto the electrode surface within the cathodic phase of lamp operation with a switched-dc or ac-current. The gas phase emitter effect of La and the influence of Na on the emitter effect of La are studied by spatially and phase-resolved pyrometric measurements of the electrode tip temperature, La atom, and ion densities by optical emission spectroscopy as well as optical broadband absorption spectroscopy and arc attachment images by short time photography. An addition of Na to the lamp filling increases the La vapor pressure within the lamp considerably, resulting in an improved gas phase emitter effect of La. Furthermore, the La vapor pressure is raised by a heating of the cold spot. In this way, conditions depending on the La vapor pressure and operating frequency are identified, at which the temperature of the electrodes becomes a minimum.

No abstract