No abstract

At the decision of the Publisher the following articles have been retracted.There are clear indicators that the submission and/or peer review process for these papers was manipulated. These indicators include but are not limited to submission patterns consistent with the use of paper mills, collusion between authors and reviewers during the review process, inappropriate subject matter as compared to the Journal's Aims and Scope, poor quality peer review and requests for inappropriate citation.The authors were contacted using email addresses provided upon submission and did not respond or did not provide a sufficient response or evidence to refute these claims. As a result, the scientific accuracy of these papers is not reliable.Adhering to the international guidelines established by the Committee on Publication Ethics, the Journal has determined these are grounds for retraction.Online First articles (these articles will not be published in an issue):

Active islanding detection techniques majorly affect power quality due to injected harmonic signals, whereas passive methods have a large non-detection zone (NDZ). This article presents a new method based on the resultant sequential impedance component (RSIC) as a new approach to island detection with zero NDZs. The abrupt variable in the conventional impedance approach was replaced by the RSIC of the inverter in this method. When the measured value exceeds the threshold range, islanding is detected by monitoring the variations in the RSIC at the point of common coupling (PCC). For proper power utilization in the identified islands, a priority-based load-shedding strategy is also recommended and implemented in this article. Its efficacy was verified in a wide range of real-world settings. It offers superior stability in various non-islanding (NIS) scenarios to prevent accidental tripping. The proposed method advantages include a cheap cost, the simplicity of implementation, independence from the number and type of distributed generation (DG) units connected, and no power quality effects. Compared to other methods reported in the literature, the obtained detection times illustrate that the proposed method is superior.

This paper proposes a hybrid optimization system depending on optimal location for electric vehicles parking lot (PL) and capacitors on distribution system to maintain voltage profile with electricity loss. The proposed system is the consolidation of Seagull optimization algorithm (SGO) and salp swarm algorithm (SSA). The migration and attacking behaviors of seagull is empowered through SSA method. By this manner, the proposed hybrid optimization scheme is known as SGOS2A method. Here, parking zone allocation with capacitor is considered to congestion management in conjunction through the compensation of reactive energy. So, one can optimally decide the size of automobile parking space, SGOS2A method is followed. Moreover, parking lot with capacitor allocation is considered to congestion control at the side of reactive power compensation. By this proper manipulate, the capacitors exact location, automobile parking space of electric vehicles on the grid, lessening of active with reactive power loss, voltage profile conversion is selected optimally. Besides, the proposed SGOS2A scheme is activated on MATLAB/Simulink site, then the efficiency is examined with different techniques. The mean, median and standard deviation of the proposed approach achieves 1.0593, 1.0915 and 0.1050.

The development of economical and sustainable eco-friendly renewable source powered power electronic converters have become more attractive in various areas such as automotive, household and industrial applications etc., Bucking and boosting of voltage according to the requirement is also much needed. So, this work proposes a solar PV powered single switch buck-boost converter which reduces implementation cost, minimal voltage and current stress across the capacitors and diodes and less switching power losses. The work structure comprises of solar PV source with modified P and O algorithm based MPPT, single switch buck-boost dc-dc converter, battery backup to store excess energy, three phase inverter with sinusoidal PWM to find optimal switching angles for harmonic control and 3Φ induction motor load. Here reduction of THD is applied to the line to line voltage of the inverter. Performance analysis of the proposed circuit is done using MATLAB/SIMULINK platform. A detailed steady state analysis of the dc-dc converter topology is also analyzed to system stability. The proposed single switch buck-boost converter is designed to provide an output voltage and current of 363V, 45.5A DC from 520V, 35A PV array. The designed converter is then employed to run a three phase full bridge inverter with 440V, 15A AC. From the simulation results, it is found that the solar powered single switch buck-boost with MPPT is stable, efficient with minimal losses and less THD with better quality output.